294 SERIES · SPHERICAL ROLLER THRUST BEARING
29430 Spherical Roller Thrust Bearing Dimensions & Specifications
29430 spherical roller thrust bearing: 150 mm bore (d), 300 mm outside diameter (D), 90 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 150 mm |
|---|---|
| Outside diameter D | 300 mm |
| Total height H | 90 mm |
| Housing washer height C | 44 mm |
| Mass | 27.9 kg |
| Catalogue dynamic load Ca | 1580 kN |
| Catalogue static load Coa | 4900 kN |
| Grease-lubricated speed | 800 rpm |
| Oil-lubricated speed | 1100 rpm |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 250 mm |
|---|---|
| Abutment dimension da | 220 mm |
| Minimum chamfer r12 | 4 mm |
| Diameter D1 | 206 mm |
| Diameter d1 | 266 mm |
| Maximum fillet ra | 3 mm |
| Offset S | 92 mm |
| Shaft washer height B | 58 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Catalog Nominal Cross-References (Brand / Legacy Codes)
Envelope reference only · Verify interchangeability| Brand / Code Type | Reference Code | Catalogue Source |
|---|---|---|
| Legacy Code | 9039430 | ZQM Catalogue P.252 |
Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.
Selection & installation
Which mounting dimensions are listed for 29430?
The 29430 catalogue lists da min = 220 mm; Da max = 250 mm; ra max = 3 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for 29430?
The listed values for 29430 are grease: 800 rpm; oil: 1100 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of 29430?
The catalogue reference mass for 29430 is 27.9 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What lubrication and minimum load rules apply to 29430 spherical roller thrust bearing?
29430 (150 × 300 × 90 mm, total height H = 90 mm and housing washer height C = 44 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
| Model | Type | Dimensions (d×D×B) |
|---|---|---|
| 61830MA | Deep Groove Ball Bearing | 150 × 190 × 20 mm |
Compare alternative series sharing the same 150 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 29430
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

