294 SERIES · SPHERICAL ROLLER THRUST BEARING
29432 Spherical Roller Thrust Bearing Dimensions & Specifications
29432 spherical roller thrust bearing: 160 mm bore (d), 320 mm outside diameter (D), 95 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 160 mm |
|---|---|
| Outside diameter D | 320 mm |
| Total height H | 95 mm |
| Housing washer height C | 46.9 mm |
| Mass | 32.8 kg |
| Catalogue dynamic load Ca | 1740 kN |
| Catalogue static load Coa | 5400 kN |
| Grease-lubricated speed | 750 rpm |
| Oil-lubricated speed | 1000 rpm |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 265 mm |
|---|---|
| Abutment dimension da | 230 mm |
| Minimum chamfer r12 | 5 mm |
| Diameter D1 | 218.5 mm |
| Diameter d1 | 285 mm |
| Maximum fillet ra | 4 mm |
| Offset S | 99 mm |
| Shaft washer height B | 34 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Selection & installation
Which mounting dimensions are listed for 29432?
The 29432 catalogue lists da min = 230 mm; Da max = 265 mm; ra max = 4 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for 29432?
The listed values for 29432 are grease: 750 rpm; oil: 1000 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of 29432?
The catalogue reference mass for 29432 is 32.8 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What lubrication and minimum load rules apply to 29432 spherical roller thrust bearing?
29432 (160 × 320 × 95 mm, total height H = 95 mm and housing washer height C = 46.9 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
| Model | Type | Dimensions (d×D×B) |
|---|---|---|
| 61832MA | Deep Groove Ball Bearing | 160 × 200 × 20 mm |
Compare alternative series sharing the same 160 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 29432
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

