294 SERIES · SPHERICAL ROLLER THRUST BEARING
29434 Spherical Roller Thrust Bearing Dimensions & Specifications
29434 spherical roller thrust bearing: 170 mm bore (d), 340 mm outside diameter (D), 103 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 170 mm |
|---|---|
| Outside diameter D | 340 mm |
| Total height H | 103 mm |
| Housing washer height C | 50 mm |
| Mass | 39.7 kg |
| Catalogue dynamic load Ca | 1680 kN |
| Catalogue static load Coa | 5800 kN |
| Grease-lubricated speed | 700 rpm |
| Oil-lubricated speed | 950 rpm |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 285 mm |
|---|---|
| Abutment dimension da | 245 mm |
| Minimum chamfer r12 | 5 mm |
| Diameter D1 | 235 mm |
| Diameter d1 | 302 mm |
| Maximum fillet ra | 4 mm |
| Offset S | 104 mm |
| Shaft washer height B | 65.5 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Selection & installation
Which mounting dimensions are listed for 29434?
The 29434 catalogue lists da min = 245 mm; Da max = 285 mm; ra max = 4 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for 29434?
The listed values for 29434 are grease: 700 rpm; oil: 950 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of 29434?
The catalogue reference mass for 29434 is 39.7 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What lubrication and minimum load rules apply to 29434 spherical roller thrust bearing?
29434 (170 × 340 × 103 mm, total height H = 103 mm and housing washer height C = 50 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
| Model | Type | Dimensions (d×D×B) |
|---|---|---|
| 61834M | Deep Groove Ball Bearing | 170 × 215 × 22 mm |
| NU3834M | Cylindrical Roller Bearing | 170 × 215 × 34 mm |
Compare alternative series sharing the same 170 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 29434
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

