294 SERIES · SPHERICAL ROLLER THRUST BEARING

29436 Spherical Roller Thrust Bearing Dimensions & Specifications

29436 spherical roller thrust bearing: 180 mm bore (d), 360 mm outside diameter (D), 109 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 180 mmD 360 mmH 109 mmCr 1870 kNMass 64.2 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 180D 360H 109Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d180 mm
Outside diameter D360 mm
Total height H109 mm
Housing washer height C51.2 mm
Mass64.2 kg
Catalogue dynamic load Ca1870 kN
Catalogue static load Coa6500 kN
Grease-lubricated speed670 rpm
Oil-lubricated speed900 rpm
Mounting dimensions & additional parameters (8)
Abutment dimension Da304 mm
Abutment dimension da265 mm
Minimum chamfer r125 mm
Diameter D1249.5 mm
Diameter d1326 mm
Maximum fillet ra4 mm
Offset S110 mm
Shaft washer height B39 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code9039436ZQM Catalogue P.253

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 29436?

The 29436 catalogue lists da min = 265 mm; Da max = 304 mm; ra max = 4 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for 29436?

The listed values for 29436 are grease: 670 rpm; oil: 900 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of 29436?

The catalogue reference mass for 29436 is 64.2 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What lubrication and minimum load rules apply to 29436 spherical roller thrust bearing?

29436 (180 × 360 × 109 mm, total height H = 109 mm and housing washer height C = 51.2 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 180 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
61836MADeep Groove Ball Bearing180 × 225 × 22 mm
NU3836MCylindrical Roller Bearing180 × 225 × 34 mm

Compare alternative series sharing the same 180 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 29436

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top