294 SERIES · SPHERICAL ROLLER THRUST BEARING

29456 Spherical Roller Thrust Bearing Dimensions & Specifications

29456 spherical roller thrust bearing: 280 mm bore (d), 520 mm outside diameter (D), 145 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 280 mmD 520 mmH 145 mmCr 3400 kNMass 134 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 280D 520H 145Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d280 mm
Outside diameter D520 mm
Total height H145 mm
Housing washer height C68 mm
Mass134 kg
Catalogue dynamic load Ca3400 kN
Catalogue static load Coa13100 kN
Grease-lubricated speed480 rpm
Oil-lubricated speed630 rpm
Mounting dimensions & additional parameters (8)
Abutment dimension Da440 mm
Abutment dimension da390 mm
Minimum chamfer r126 mm
Diameter D1384 mm
Diameter d1480 mm
Maximum fillet ra5 mm
Offset S160 mm
Shaft washer height B104 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code9039456ZQM Catalogue P.254

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 29456?

The 29456 catalogue lists da min = 390 mm; Da max = 440 mm; ra max = 5 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for 29456?

The listed values for 29456 are grease: 480 rpm; oil: 630 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of 29456?

The catalogue reference mass for 29456 is 134 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What lubrication and minimum load rules apply to 29456 spherical roller thrust bearing?

29456 (280 × 520 × 145 mm, total height H = 145 mm and housing washer height C = 68 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 280 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
23856CA/W33Spherical Roller Bearing280 × 350 × 52 mm
61856MDeep Groove Ball Bearing280 × 350 × 33 mm
NU3856MCylindrical Roller Bearing280 × 350 × 52 mm

Compare alternative series sharing the same 280 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 29456

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top