294 SERIES · SPHERICAL ROLLER THRUST BEARING
29460 Spherical Roller Thrust Bearing Dimensions & Specifications
29460 spherical roller thrust bearing: 300 mm bore (d), 540 mm outside diameter (D), 145 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 300 mm |
|---|---|
| Outside diameter D | 540 mm |
| Total height H | 145 mm |
| Housing washer height C | 70 mm |
| Mass | 140.0 kg |
| Catalogue dynamic load Ca | 3500 kN |
| Catalogue static load Coa | 13700 kN |
| Grease-lubricated speed | 450 rpm |
| Oil-lubricated speed | 600 rpm |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 460 mm |
|---|---|
| Abutment dimension da | 410 mm |
| Minimum chamfer r12 | 6 mm |
| Diameter D1 | 402 mm |
| Diameter d1 | 500 mm |
| Maximum fillet ra | 5 mm |
| Offset S | 175 mm |
| Shaft washer height B | 52 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Catalog Nominal Cross-References (Brand / Legacy Codes)
Envelope reference only · Verify interchangeability| Brand / Code Type | Reference Code | Catalogue Source |
|---|---|---|
| Legacy Code | 9039460 | ZQM Catalogue P.254 |
Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.
Selection & installation
Which mounting dimensions are listed for 29460?
The 29460 catalogue lists da min = 410 mm; Da max = 460 mm; ra max = 5 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for 29460?
The listed values for 29460 are grease: 450 rpm; oil: 600 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of 29460?
The catalogue reference mass for 29460 is 140.0 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What lubrication and minimum load rules apply to 29460 spherical roller thrust bearing?
29460 (300 × 540 × 145 mm, total height H = 145 mm and housing washer height C = 70 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
| Model | Type | Dimensions (d×D×B) |
|---|---|---|
| 23860CA/W33 | Spherical Roller Bearing | 300 × 380 × 60 mm |
| 61860MA | Deep Groove Ball Bearing | 300 × 380 × 38 mm |
Compare alternative series sharing the same 300 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 29460
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

