294 SERIES · SPHERICAL ROLLER THRUST BEARING

29464 Spherical Roller Thrust Bearing Dimensions & Specifications

29464 spherical roller thrust bearing: 320 mm bore (d), 580 mm outside diameter (D), 155 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 320 mmD 580 mmH 155 mmCr 3650 kNMass 178 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
d 320D 580H 155Spherical Roller Thrust Bearing (292/293/294)

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d320 mm
Outside diameter D580 mm
Total height H155 mm
Housing washer height C75 mm
Mass178 kg
Catalogue dynamic load Ca3650 kN
Catalogue static load Coa14600 kN
Grease-lubricated speed430 rpm
Oil-lubricated speed560 rpm
Mounting dimensions & additional parameters (8)
Abutment dimension Da495 mm
Abutment dimension da435 mm
Minimum chamfer r127.5 mm
Diameter D1436 mm
Diameter d1555 mm
Maximum fillet ra6 mm
Offset S191 mm
Shaft washer height B108 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code9039464ZQM Catalogue P.254

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for 29464?

The 29464 catalogue lists da min = 435 mm; Da max = 495 mm; ra max = 6 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for 29464?

The listed values for 29464 are grease: 430 rpm; oil: 560 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of 29464?

The catalogue reference mass for 29464 is 178 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

What lubrication and minimum load rules apply to 29464 spherical roller thrust bearing?

29464 (320 × 580 × 155 mm, total height H = 155 mm and housing washer height C = 75 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.

Other Bearing Series with 320 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
23864CA/W33Spherical Roller Bearing320 × 400 × 60 mm
24864CA/W33Spherical Roller Bearing320 × 400 × 80 mm
61864MADeep Groove Ball Bearing320 × 400 × 38 mm

Compare alternative series sharing the same 320 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for 29464

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top