294 SERIES · SPHERICAL ROLLER THRUST BEARING
29488/HV Spherical Roller Thrust Bearing Dimensions & Specifications
29488/HV spherical roller thrust bearing: 440 mm bore (d), 780 mm outside diameter (D), 206 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 440 mm |
|---|---|
| Outside diameter D | 780 mm |
| Total height H | 206 mm |
| Housing washer height C | 100 mm |
| Mass | 346.6 kg |
| Catalogue dynamic load Ca | 7880 kN |
| Catalogue static load Coa | 34000 kN |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 670 mm |
|---|---|
| Abutment dimension da | 595 mm |
| Minimum chamfer r12 | 9.5 mm |
| Diameter D1 | 588 mm |
| Diameter d1 | 660 mm |
| Maximum fillet ra | 8 mm |
| Offset S | 260 mm |
| Shaft washer height B | 110 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Selection & installation
Which mounting dimensions are listed for 29488/HV?
The 29488/HV catalogue lists da min = 595 mm; Da max = 670 mm; ra max = 8 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What is the reference mass of 29488/HV?
The catalogue reference mass for 29488/HV is 346.6 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What are the main dimensions and load ratings of 29488/HV?
In the ZQM General Catalogue, 29488/HV has nominal boundary dimensions of Array. Catalog load ratings: Ca 7880 kN, C0a 34000 kN. Confirm exact clearance, cage design and tolerance class against your drawing prior to ordering.
What lubrication and minimum load rules apply to 29488/HV spherical roller thrust bearing?
29488/HV (440 × 780 × 206 mm, total height H = 206 mm and housing washer height C = 100 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
| Model | Type | Dimensions (d×D×B) |
|---|---|---|
| 61888 | Deep Groove Ball Bearing | 440 × 540 × 46 mm |
Compare alternative series sharing the same 440 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 29488/HV
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

