294 SERIES · SPHERICAL ROLLER THRUST BEARING
29492 Spherical Roller Thrust Bearing Dimensions & Specifications
29492 spherical roller thrust bearing: 460 mm bore (d), 800 mm outside diameter (D), 206 mm height (H). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings.
| Bore d | 460 mm |
|---|---|
| Outside diameter D | 800 mm |
| Total height H | 206 mm |
| Housing washer height C | 100 mm |
| Mass | 420 kg |
| Catalogue dynamic load Ca | 6900 kN |
| Catalogue static load Coa | 28300 kN |
| Oil-lubricated speed | 380 rpm |
Mounting dimensions & additional parameters (8)
| Abutment dimension Da | 690 mm |
|---|---|
| Abutment dimension da | 615 mm |
| Minimum chamfer r12 | 9.5 mm |
| Diameter D1 | 608 mm |
| Diameter d1 | 765 mm |
| Maximum fillet ra | 8 mm |
| Offset S | 272 mm |
| Shaft washer height B | 74 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Selection & installation
Which mounting dimensions are listed for 29492?
The 29492 catalogue lists da min = 615 mm; Da max = 690 mm; ra max = 8 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for 29492?
The listed values for 29492 are oil: 380 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of 29492?
The catalogue reference mass for 29492 is 420 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
What lubrication and minimum load rules apply to 29492 spherical roller thrust bearing?
29492 (460 × 800 × 206 mm, total height H = 206 mm and housing washer height C = 100 mm) uses ISO 104 asymmetrical barrel rollers on a self-aligning spherical housing washer for high unidirectional axial loads. Oil lubrication is preferred under heavy load or continuous duty, and adequate minimum axial load must be maintained to prevent roller skidding.
| Model | Type | Dimensions (d×D×B) |
|---|---|---|
| 24892CAF3/W33 | Spherical Roller Bearing | 460 × 580 × 118 mm |
| 61892 | Deep Groove Ball Bearing | 460 × 580 × 56 mm |
Compare alternative series sharing the same 460 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
- Spherical Roller Thrust Bearings (293 vs 294): Minimum Axial Load, Oil Lubrication, and Alignment
- 29000 Series Spherical Roller Thrust Bearings (292, 293, 294): Housing, Minimum Load & Oil Bath
- Bearing Cross Reference & ISO Suffix Guide: Comparing SKF, FAG, NSK, NTN and ZQM
- 294 Series Spherical Roller Thrust Bearings
- ISO 281 Bearing Life Calculator
DIRECT FACTORY SOURCING
Request a Quote for 29492
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

