QJF10 SERIES · FOUR-POINT CONTACT BALL BEARING
QJF1038X1MB Four-Point Contact Ball Bearing Dimensions & Specifications
QJF1038X1MB four-point contact ball bearing: 190 mm bore (d), 289.5 mm outside diameter (D), 46 mm width (B). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.
Nominal Cross-Section & Boundary Dimensions
Unit: mm · Schematic (not to scale)Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings. Note: Specific split-ring configuration (inner vs. outer ring) for QJF designations is confirmed per engineering drawing.
| Bore d | 190 mm |
|---|---|
| Outside diameter D | 289.5 mm |
| Width B | 46 mm |
| Mass | 11.4 kg |
| Catalogue dynamic load Cr | 340 kN |
| Catalogue static load Cor | 510 kN |
| Grease-lubricated speed | 1600 rpm |
| Oil-lubricated speed | 2200 rpm |
Mounting dimensions & additional parameters (10)
| Abutment dimension Da | 278 mm |
|---|---|
| Abutment dimension da | 202 mm |
| Minimum chamfer r12 | 2.1 mm |
| Factor X | 0.6 |
| Factor Y0 | 0.58 |
| Factor Y1 | 0.66 |
| Factor Y2 | 1.07 |
| Factor e | 0.95 |
| Maximum fillet ra | 2 mm |
| Load centre dimension a | 168 mm |
Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.
Catalog Nominal Cross-References (Brand / Legacy Codes)
Envelope reference only · Verify interchangeability| Brand / Code Type | Reference Code | Catalogue Source |
|---|---|---|
| Legacy Code | 116738 | ZQM Catalogue P.50 |
Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.
Selection & installation
Which mounting dimensions are listed for QJF1038X1MB?
The QJF1038X1MB catalogue lists da min = 202 mm; Da max = 278 mm; ra max = 2 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.
What speed values are available for QJF1038X1MB?
The listed values for QJF1038X1MB are grease: 1600 rpm; oil: 2200 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.
What is the reference mass of QJF1038X1MB?
The catalogue reference mass for QJF1038X1MB is 11.4 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.
How should QJF1038X1MB four-point contact ball bearing be loaded and mounted?
QJF1038X1MB (190 × 289.5 × 46 mm) is designed for pure axial or predominantly axial bidirectional loads. When paired with a cylindrical roller bearing strictly as an axial locating unit, provide radial clearance between the outer ring and housing bore so it carries no radial load. Confirm specific split-ring configuration (inner vs. outer ring) for this QJF designation per drawing.
Related ZQM Products & Engineering Guides
Featured Stock & Production Models
Technical Guides & Series
DIRECT FACTORY SOURCING
Request a Quote for QJF1038X1MB
Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

