QJF1052X1MB Four-Point Contact Ball Bearing Overview
Engineered with a non-standard outer diameter of 399.5 mm (0.5 mm smaller than standard integer 400 mm QJ 1052 bearings), the QJF1052X1MB single-row four-point contact ball bearing (260 × 399.5 × 65 mm, reference mass 31.3 kg) handles bidirectional axial thrust in compact rolling mill chocks, heavy compressors, and gearbox locating stacks. Per ZQM Bearings’ 259-page general catalogue, it delivers a basic dynamic load rating Cr of 550 kN and basic static load rating C0r of 1,000 kN.
Critical Housing Fit Alert (-0.5 mm Special OD): The 399.5 mm outer diameter is intentionally undersized relative to a nominal 400 mm housing bore so the outer ring remains radially free (floating) and carries pure bidirectional axial load while an adjacent radial roller bearing supports 100% of radial force. Always verify housing bore dimensions and tolerances against your equipment drawing before ordering.
QJF1052X1MB Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 260 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 399.5 mm |
| Boundary Dimensions & Weight | Width (B) | 65 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 31.3 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 550 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 1000 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 1000 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 1500 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 278 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 383 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 4.0 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 3 mm |
| Abutment & Fillet Dimensions | Load center distance (a) | 231 mm |
| Calculation Factors | Calculation factor (e) | 0.95 |
| Calculation Factors | Axial load factor (static) (Y0) | 0.58 |
| Calculation Factors | Axial load factor (Y1) | 0.66 |
| Calculation Factors | Axial load factor (Y2) | 1.07 |
| Calculation Factors | Radial load factor (X) | 0.6 |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
Structural Design and Axial Locating Engineering
- 35° Contact Angle & Split-Ring Architecture: Accommodates heavy reversing axial loads in both directions within a single 65 mm axial width (load center a = 231 mm), replacing back-to-back paired angular contact bearings where axial space is restricted.
- Cylindrical Bore (Non-Tapered): Manufactured with a straight 260 mm cylindrical bore; standard QJF bearings do not use tapered K sleeves.
- Machined Solid Cage (MB): Inner-ring guided machined solid cage construction suited for sustained industrial speeds (reference grease limit 1,000 r/min, oil limit 1,500 r/min); exact cage alloy and tolerance class are confirmed on the order drawing.
Typical Industrial Equipment Applications
- Steel Rolling Mill Locating Stacks: Paired beside four-row cylindrical rolling mill bearings (Steel and Rolling Mills Hub) to take pure bidirectional axial thrust.
- Heavy Helical Gearboxes & Compressors: High-speed input and intermediate shaft axial locating positions where radial loads are carried by adjacent NU/NJ cylindrical roller bearings.
- Large Vertical Pumps & Rotary Drives: Compact axial thrust control under reversing operating cycles.
ISO Nominal Cross-Reference for QJF1052X1MB
| Brand | Nominal Series Reference | Critical OD Check | Engineering Note |
|---|---|---|---|
| ZQM Bearings | QJF1052X1MB | 399.5 mm (-0.5 mm special OD) | Verified in ZQM 259-page General Catalogue |
| Standard ISO Series | QJ 1052 / QJF 10.. | 400 mm (standard integer OD) | NOT directly interchangeable on housing fit without verifying 399.5 vs 400 mm bore |
ISO Nominal Boundary Disclaimer: Cross-brand references indicate nominal bore/width series alignment only and do not promise drop-in interchangeability. Always confirm outer diameter (399.5 mm vs 400 mm), axial internal clearance, and housing drawings prior to replacement.
Mounting Abutment and Lubrication Guidelines
Verify shaft shoulder diameter da min = 278 mm, housing shoulder diameter Da max = 383 mm, and maximum fillet radius ra max = 3 mm. Ensure the outer ring is clamped axially with proper anti-rotation pin or radial clearance so it does not experience radial preloading. For speed-load evaluation, run your duty cycle in our ISO 281 Bearing Life Calculator or verify nomenclature in our Bearing Suffix Decoder.
Factory Quality Control and Export Supply
Manufactured at Wafangdian Qunma Bearing Manufacturing Co., Ltd. (ISO 9001 & ISO 14001 certified) with Ningbo export engineering support and Shanghai consolidation. Actual supplied clearance, tolerance class, and inspection documentation are confirmed in writing before production. Contact ZQM Bearings for drawing review and factory quotation.
Frequently Asked Questions — QJF1052X1MB
Why does QJF1052X1MB have a 399.5 mm outer diameter instead of 400 mm?
The 399.5 mm outer diameter is 0.5 mm smaller than the standard 400 mm QJ 1052 OD so the bearing sits radially free inside a nominal 400 mm housing bore. This prevents radial load from transferring into the four-point contact ball bearing when paired alongside a radial roller bearing.
Can I replace a 400 mm QJ 1052 directly with QJF1052X1MB (399.5 mm)?
Only if your equipment drawing specifies a radially floating 399.5 mm outer ring inside a 400 mm housing. Never substitute between 399.5 mm and 400 mm outer diameters without checking the housing bore tolerance and anti-rotation locking design.
What are the verified load ratings and weight of QJF1052X1MB?
Per ZQM Bearings’ catalog database, QJF1052X1MB (260 × 399.5 × 65 mm) has a basic dynamic load rating Cr of 550 kN, basic static load rating C0r of 1,000 kN, reference mass of 31.3 kg, and limiting speeds of 1,000 r/min (grease) / 1,500 r/min (oil).
Does QJF1052X1MB have a tapered bore?
No. QJF1052X1MB has a standard 260 mm straight cylindrical bore and does not mount on tapered K or K30 adapter sleeves.
What details should I send to quote QJF1052X1MB?
Provide designation QJF1052X1MB, confirm whether you require the 399.5 mm special OD (or standard 400 mm), specify clearance and quantity, and share your destination port via our Contact page.



