QJF10 SERIES · FOUR-POINT CONTACT BALL BEARING

QJF1068MB Four-Point Contact Ball Bearing Dimensions & Specifications

QJF1068MB four-point contact ball bearing: 340 mm bore (d), 520 mm outside diameter (D), 82 mm width (B). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 340 mmD 520 mmB 82 mmCr 780 kNMass 68.8 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
Four-Point Contact Ball Bearing (Split Ring)d 340D 520B 82

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings. Note: Specific split-ring configuration (inner vs. outer ring) for QJF designations is confirmed per engineering drawing.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d340 mm
Outside diameter D520 mm
Width B82 mm
Mass68.8 kg
Catalogue dynamic load Cr780 kN
Catalogue static load Cor1700 kN
Grease-lubricated speed800 rpm
Oil-lubricated speed1100 rpm
Mounting dimensions & additional parameters (10)
Abutment dimension Da498 mm
Abutment dimension da362 mm
Minimum chamfer r125.0 mm
Factor X0.6
Factor Y00.58
Factor Y10.66
Factor Y21.07
Factor e0.95
Maximum fillet ra4 mm
Load centre dimension a301 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code116168ZQM Catalogue P.52

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for QJF1068MB?

The QJF1068MB catalogue lists da min = 362 mm; Da max = 498 mm; ra max = 4 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for QJF1068MB?

The listed values for QJF1068MB are grease: 800 rpm; oil: 1100 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of QJF1068MB?

The catalogue reference mass for QJF1068MB is 68.8 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

How should QJF1068MB four-point contact ball bearing be loaded and mounted?

QJF1068MB (340 × 520 × 82 mm) is designed for pure axial or predominantly axial bidirectional loads. When paired with a cylindrical roller bearing strictly as an axial locating unit, provide radial clearance between the outer ring and housing bore so it carries no radial load. Confirm specific split-ring configuration (inner vs. outer ring) for this QJF designation per drawing.

Other Bearing Series with 340 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
23868CA/W33Spherical Roller Bearing340 × 420 × 60 mm
61868Deep Groove Ball Bearing340 × 420 × 38 mm

Compare alternative series sharing the same 340 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for QJF1068MB

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top