QJF10 SERIES · FOUR-POINT CONTACT BALL BEARING

QJF1072MB Four-Point Contact Ball Bearing Dimensions & Specifications

QJF1072MB four-point contact ball bearing: 360 mm bore (d), 540 mm outside diameter (D), 82 mm width (B). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 360 mmD 540 mmB 82 mmCr 793 kNMass 73.5 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
Four-Point Contact Ball Bearing (Split Ring)d 360D 540B 82

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings. Note: Specific split-ring configuration (inner vs. outer ring) for QJF designations is confirmed per engineering drawing.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d360 mm
Outside diameter D540 mm
Width B82 mm
Mass73.5 kg
Catalogue dynamic load Cr793 kN
Catalogue static load Cor1800 kN
Grease-lubricated speed800 rpm
Oil-lubricated speed1100 rpm
Mounting dimensions & additional parameters (10)
Abutment dimension Da518 mm
Abutment dimension da382 mm
Minimum chamfer r125.0 mm
Factor X0.6
Factor Y00.58
Factor Y10.66
Factor Y21.07
Factor e0.95
Maximum fillet ra4 mm
Load centre dimension a315 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code116172ZQM Catalogue P.52

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for QJF1072MB?

The QJF1072MB catalogue lists da min = 382 mm; Da max = 518 mm; ra max = 4 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for QJF1072MB?

The listed values for QJF1072MB are grease: 800 rpm; oil: 1100 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of QJF1072MB?

The catalogue reference mass for QJF1072MB is 73.5 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

How should QJF1072MB four-point contact ball bearing be loaded and mounted?

QJF1072MB (360 × 540 × 82 mm) is designed for pure axial or predominantly axial bidirectional loads. When paired with a cylindrical roller bearing strictly as an axial locating unit, provide radial clearance between the outer ring and housing bore so it carries no radial load. Confirm specific split-ring configuration (inner vs. outer ring) for this QJF designation per drawing.

Other Bearing Series with 360 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
23872CA/W33Spherical Roller Bearing360 × 440 × 60 mm
61872Deep Groove Ball Bearing360 × 440 × 38 mm

Compare alternative series sharing the same 360 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for QJF1072MB

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top