QJF10 SERIES · FOUR-POINT CONTACT BALL BEARING

QJF1096MB Four-Point Contact Ball Bearing Dimensions & Specifications

QJF1096MB four-point contact ball bearing: 480 mm bore (d), 700 mm outside diameter (D), 100 mm width (B). Review the available technical values below. Matching dimensions alone do not confirm interchangeability between designations or suffixes.

d 480 mmD 700 mmB 100 mmCr 1060 kNMass 137 kg

Nominal Cross-Section & Boundary Dimensions

Unit: mm · Schematic (not to scale)
Four-Point Contact Ball Bearing (Split Ring)d 480D 700B 100

Schematic cross-section illustrating this bearing family with nominal catalog dimensions for this designation. Verify exact chamfers, cage geometry, and lubrication grooves against engineering drawings. Note: Specific split-ring configuration (inner vs. outer ring) for QJF designations is confirmed per engineering drawing.

Technical specifications

Source: ZQM Master Catalogue · Units: mm / kN / kg
Bore d480 mm
Outside diameter D700 mm
Width B100 mm
Mass137 kg
Catalogue dynamic load Cr1060 kN
Catalogue static load Cor2800 kN
Grease-lubricated speed560 rpm
Oil-lubricated speed750 rpm
Mounting dimensions & additional parameters (10)
Abutment dimension Da672 mm
Abutment dimension da508 mm
Minimum chamfer r126.0 mm
Factor X0.6
Factor Y00.58
Factor Y10.66
Factor Y21.07
Factor e0.95
Maximum fillet ra5 mm
Load centre dimension a413 mm

Fields without confirmed values are omitted. Final supply configuration and application suitability require technical confirmation.

Catalog Nominal Cross-References (Brand / Legacy Codes)

Envelope reference only · Verify interchangeability
Brand / Code TypeReference CodeCatalogue Source
Legacy Code116196ZQM Catalogue P.53

Notice: Cross-references above are listed from the ZQM Master Catalogue for nominal boundary-dimension lookup only. Internal clearance, cage design, roller profile, and load ratings vary by manufacturer; verify drawings before substitution.

Selection & installation

Which mounting dimensions are listed for QJF1096MB?

The QJF1096MB catalogue lists da min = 508 mm; Da max = 672 mm; ra max = 5 mm. Check these symbols against the bearing drawing and the shaft/housing shoulders; they are not shaft or housing fit tolerances.

What speed values are available for QJF1096MB?

The listed values for QJF1096MB are grease: 560 rpm; oil: 750 rpm. These catalogue references do not determine a safe operating speed on their own. Confirm load, clearance, lubrication and heat conditions for the application.

What is the reference mass of QJF1096MB?

The catalogue reference mass for QJF1096MB is 137 kg. Confirm the supplied assembly and packed shipment weight separately when planning handling or transport.

How should QJF1096MB four-point contact ball bearing be loaded and mounted?

QJF1096MB (480 × 700 × 100 mm) is designed for pure axial or predominantly axial bidirectional loads. When paired with a cylindrical roller bearing strictly as an axial locating unit, provide radial clearance between the outer ring and housing bore so it carries no radial load. Confirm specific split-ring configuration (inner vs. outer ring) for this QJF designation per drawing.

Other Bearing Series with 480 mm Bore

Envelope reference only · Not direct interchange
Swipe horizontally to view full table
ModelTypeDimensions (d×D×B)
23896CAF3/W33Spherical Roller Bearing480 × 600 × 90 mm
61896Deep Groove Ball Bearing480 × 600 × 56 mm

Compare alternative series sharing the same 480 mm shaft bore diameter to review envelope dimensions (D × B) and ring/rib configurations. Shared bore diameter does not imply direct interchangeability.

Related ZQM Products & Engineering Guides

DIRECT FACTORY SOURCING

Request a Quote for QJF1096MB

Share your required quantity, clearance (CN/C3/C4), and destination with ZQM Bearings. Mixed-model trial lots and OEM drawings welcome.

Scroll to Top