Steel, Metallurgy & Rolling Mills

Steel, Metallurgy and Rolling Mill Bearings

Engineered for integrated steelworks, hot and cold strip mills, aluminum rolling plants, and continuous slab casters. ZQM supplies straight-bore FC / FCD / FCDP four-row cylindrical, TQO / TQI four-row tapered, and large-bore 230 / 240 / 241 spherical roller bearings with verified catalogue tolerances and chock-ready consistency.

484+FC / FCD / FCDP Four-Row Models in DB
690+TQO / TQI Four-Row Tapered Entries
120–420 mmFeatured Mill & Caster Bore Range
ISO 15 / 355Radial & Tapered Boundary Compliance

Bearing Selection by Steel Mill & Caster Position

Match roll-neck chocks, continuous caster segments, pinion stands, and heavy mill drives to verified ZQM roller bearing architectures.

Four-row cylindrical roller bearing representative image for rolling mill roll necks
Work & Backup Roll Necks

Hot & Cold Rolling Mill Roll-Neck Chocks

Four-row straight-bore FC / FCD / FCDP cylindrical roller bearings carry extreme radial separating loads inside compact chock sections while allowing rapid roll-change swaps. Pair with dedicated thrust bearings in the chock for bidirectional axial control.

Heavy tapered roller bearing representative image for rolling mill combined radial and axial thrust
Combined Radial + Axial Roll Necks

Four-Row TQO Roll Necks & Mill Thrust Units

Where a single bearing assembly must locate the roll axially in both directions under combined separating and axial loads, TQO / TQI four-row tapered roller units and heavy 322 / 323 tapered roller sets handle roll-neck and auxiliary thrust duties per ISO 355.

Large-bore spherical roller bearing representative image for continuous casters and steel mill drives
Continuous Casters & Trunnions

Continuous Slab Casters & Converter Trunnions

Low-speed, high-heat caster segment rolls, coiler mandrels, and converter trunnions face radiant slab heat, cooling spray, and structural deflection. Large-bore 230 / 231 (optional 1:12 K) and wide 240 / 241 (optional 1:30 K30) spherical bearings provide self-aligning durability.

Heavy single-row cylindrical roller bearing representative image for steel mill pinion stands and roller tables
Pinion Stands & Runout Tables

Mill Pinion Gearboxes & Roller Table Drives

High-torque mill pinion stands and hot runout roller tables require separable straight-bore NJ / NU cylindrical roller bearings (NJ locating axially in one direction; NU floating thermal expansion within permissible limits) paired with heavy 231 / 232 spherical output bearings.

Verified Steel Rolling Mill & Metallurgy Reference Bearings

Verified Specifications · ZQM Engineering Catalogue
Model Series / Design Dimensions (d × D × B/T) Basic Load Cr / C0r Ref. Mass Typical Steelworks Position Datasheet
FCD5678275 Four-Row Cylindrical (Fw=308) 280 × 390 × 275 mm 2,720 / 6,130 kN 105 kg Hot/cold strip work & backup roll necks View Spec
FCD4468210 Four-Row Cylindrical (Fw=250) 220 × 340 × 210 mm 1,910 / 3,850 kN 70.5 kg Section & medium-plate roll necks Catalog
FCDP4468290 Pin-Cage Four-Row (Fw=250) 220 × 340 × 290 mm 2,980 / 5,010 kN 96.5 kg High-load wide-face rolling stands Catalog
220TQO320-3 Four-Row Tapered (TQO) 220 × 320 × 250 mm (T) Per drawing / catalog 68.0 kg Combined radial + axial roll-neck chocks Catalog
23080 CA/W33 Large Spherical (230, 1:12 K opt.) 400 × 600 × 148 mm 2,970 / 5,900 kN 146 kg Continuous caster rolls & ladle turrets View Spec
23084 CA/W33 Large Spherical (230, 1:12 K opt.) 420 × 620 × 150 mm 2,910 / 5,850 kN 151 kg Heavy converter trunnions & drives View Spec
24152 CA/W33 Wide Spherical (241, 1:30 K30 opt.) 260 × 440 × 180 mm 2,560 / 4,700 kN 109 kg Slab caster segments & heavy coilers View Spec
24060 CA/W33 Wide Spherical (240, 1:30 K30 opt.) 300 × 460 × 160 mm 2,310 / 4,600 kN 93.6 kg Caster guide rolls & tension reels View Spec
23160 CA/W33 Heavy Spherical (231, 1:12 K opt.) 300 × 500 × 160 mm 2,670 / 4,800 kN 125 kg Mill main reducer output shafts View Spec
NJ326EM Single-Row Cylindrical (Straight Bore) 130 × 280 × 58 mm 615 / 735 kN 19.5 kg Pinion stands & hot runout roller tables View Spec
32324 Heavy Tapered (323, B=86 / C=69) 120 × 260 × 90.5 mm (T) 770 / 1,060 kN 21.8 kg Pinion bevel shafts & auxiliary thrust View Spec

Engineering Notice: Nominal boundary dimensions follow ISO 15 (radial) and ISO 355 (tapered overall width T). Cross-references to international mill designations match nominal envelope dimensions only; always verify under-roller diameter Fw, cage execution, lubrication grooves, and radial clearance or axial setting per mill chock drawing before installation.

Four Critical Engineering Checks for Steel Mill Bearings

Prevent premature roll-neck spalling, chock seizure, and unplanned mill shutdowns by confirming these parameters during specification.

1. Separable Fw & Radial Clearance Control (C3 / C4)

Hot-strip and continuous-caster shafts experience substantial thermal gradients between the hot roll neck and water-cooled chock housing. Specify C3 or C4 unmounted radial clearance based on interference-fit expansion and shaft-to-housing temperature delta, and confirm exact Fw whenever separable four-row inner rings remain on spare rolls.

Read Rolling Mill FCD / FCDP Guide

2. Tapered Bore Discipline: 1:30 (K30) vs 1:12 (K) vs Straight Bore

Do not mix sleeve taper ratios across mill equipment. Wide 240 and 241 series spherical bearings use a 1:30 taper (K30) when ordered with tapered bores, while 230, 231, and 232 series use a 1:12 taper (K). Standard FC/FCD/FCDP four-row roll-neck bearings and NJ/NU pinion bearings use straight cylindrical bores unless a dedicated tapered roll-neck drawing is specified.

Read K vs K30 Tapered Bore Guide

3. Axial Setting on Tapered Roll Necks & Thrust Pairing

Four-row FC/FCD/FCDP cylindrical bearings carry radial load only and require a separate thrust bearing in the chock. On TQO/TQI four-row tapered units and opposed 322/323 bevel-shaft pairs, set internal axial clearance or preload via matched spacer rings and axial end-play checks—never via radial feeler gauges.

Read Tapered Preload & Axial Setting Guide

4. Scale, Cooling Water & Oil-Air Lubrication Protection

Mill scale and high-pressure descaling water accelerate abrasive wear and moisture corrosion. Combine W33 lubrication grooves and outer-ring oil holes with chock oil-air, oil-mist, or continuous EP grease purging and multi-lip chock seals to maintain stable lubricant film thickness under shock loads.

Read Heavy Bearing Damage Analysis
Continuous casting and rolling mill heavy bearing application in steelworks
Direct Manufacturer Support for Steelworks OEMs & MRO From single-stand replacement chocks to multi-stand annual MRO contracts, ZQM verifies boundary dimensions, Fw matching, clearance group, and export-grade anti-rust crating before shipment.

Rolling Mill & Caster RFQ Checklist

Include these 5 items in your inquiry so our bearing engineers can verify interchangeability and lead time without back-and-forth delays:

  • Complete Designation or Drawing: Original bearing code or roll-neck drawing with d × D × B/T and separable Fw.
  • Stand & Operating Position: Hot/cold work roll, backup roll, continuous caster segment, converter trunnion, or pinion stand.
  • Bore, Clearance & Cage Execution: Straight bore vs K (1:12) / K30 (1:30), C3 / C4 clearance, solid brass or pin-type cage.
  • Lubrication & Thermal Conditions: Oil-air, oil-mist, circulating oil, or EP grease, plus expected roll-neck operating temperature.
  • Order Volume & Delivery Target: Trial chock set or scheduled plant maintenance batch, destination port, and inspection scope.
Send Mill Spec for Factory Quote

Steel & Rolling Mill Bearing FAQs

Practical engineering answers for steelworks maintenance engineers and OEM rolling-mill procurement teams.

When should rolling mill stands use FC / FCD / FCDP four-row cylindrical bearings instead of TQO four-row tapered bearings?

Use FC, FCD, or FCDP four-row cylindrical roller bearings when work or backup roll necks require maximum radial capacity inside a compact section and high roll-change speed (separable straight-bore inner rings stay on the roll neck). Because four-row cylindrical bearings take radial load only, they must pair with a separate axial thrust bearing (such as double-direction tapered roller thrust, four-point contact ball, or deep-groove ball locating bearings) in the chock. Choose TQO / TQI four-row tapered roller bearings when a single compact roll-neck assembly must support both high radial separating force and bidirectional axial thrust.

Why is roller under-diameter (Fw) verification mandatory when replacing separable four-row rolling mill bearings?

In hot and cold rolling mills, roll-neck inner rings remain interference-fitted on spare roll shafts while outer-ring/roller assemblies rotate between chocks. Interchanging assemblies across mill stands or brands requires verifying the exact under-roller raceway diameter Fw (for example, Fw = 308 mm on FCD5678275 or Fw = 250 mm on FCD4468210) and matched radial internal clearance—matching nominal d × D × B alone is not sufficient for separable chock interchangeability.

How do tapered bore ratios differ between 240/241 continuous caster bearings and 230/231/232 mill drive bearings?

Standard catalog units in these spherical series are supplied with straight cylindrical bores. Where sleeve-mounted tapered bores are specified, wide-section 240 and 241 series bearings use a 1:30 taper (K30), whereas 230, 231, and 232 series bearings use a 1:12 taper (K). Four-row FC/FCD/FCDP cylindrical bearings and NJ/NU pinion bearings use straight cylindrical bores unless a dedicated tapered roll-neck drawing is engineered.

What engineering details should steelworks OEMs and MRO buyers send for a rolling mill bearing quotation?

Provide the full original bearing designation or roll-neck drawing (including bore, OD, total width B or T, Fw, radial clearance group C3/C4, cage design, and lubrication holes/grooves), mill stand position (work roll, backup roll, continuous caster, or pinion stand), lubrication method (oil-air, oil-mist, circulating oil, or EP grease), and batch quantity. ZQM verifies boundary tolerances, clearance, and inspection scope before quoting.

Need Technical Verification for Rolling Mill or Caster Bearings?

Share your bearing designations, roll-neck drawings, Fw / clearance specifications, and maintenance schedule. ZQM’s engineering and export team will confirm exact dimensional matching and factory lead times.

Scroll to Top