The 2312 self-aligning ball bearing (60 × 130 × 46 mm, ISO 15 Dimension Series 23) delivers the stoutest ball-bearing cross-section available on a 60 mm shaft. Its 46 mm axial width and deep spherical outer track make it a dependable choice for wood-chipper infeed rollers and paper-mill felt-guide roll housings where wide roll spans bow appreciably between side frames. Offered in 60 mm cylindrical bore or 2312K (1:12 tapered bore) fitted with the wide-series H2312 adapter sleeve for 55 mm smooth roll journals.
| ISO 15 Series 23 Metric | Symbol | 2312 Nominal Spec | Pulp / Woodyard Notes |
|---|---|---|---|
| Straight Bore Diameter | d | 60 mm | Direct fit on stepped roll trunnion |
| Outside Diameter | D | 130 mm | Heavy Series 23 housing bore (SNL 513-610) |
| Extra-Wide Ring Width | B | 46 mm | 15 mm wider than medium-series 1312 (31 mm) |
| Optional Tapered Bore | 2312K | 1:12 Tapered Bore | Pairs strictly with H2312 sleeve (55 mm shaft) |
| Alignment & Side Clearance | Sphered Outer Ring | ~2.5° – 3° Tilt | Verify ball side-face protrusion against spacers |
| Load Ratings, Speed & Cage | Cr / C0r / rpm / Cage | Factory Drawing Verified | Confirmed per retainer & clearance at quote |
2312 Heavy 46 mm Envelope for Long Flexible Rolls & Frame Distortion
Paper-machine felt-guide rolls and wire-return rolls span three to six meters across humid steel frames, while toothed wood-chipper infeed rollers pivot up and down on hinged swing arms whenever uneven logs enter the throat. Both machines bend 60 mm roll necks visibly and throw bearing pedestals out of square under frame distortion. With its broad 46 mm width and large twin rows of precision balls, the 2312 carries substantially higher radial and combined axial loads than narrower Series 12 or 13 ball units while staying remarkably low-friction—critical on unpowered paper felt rolls that must turn effortlessly under fabric drag alone so the felt never skids or streaks.
Engineers designing housings for wide Series 23 bearings must verify one geometric detail early: on several heavy Series 23 executions, the large rolling balls can protrude fractionally beyond the 46 mm side faces of the inner and outer rings. Always check adjacent labyrinth collars, locking washers, and shoulder reliefs against our factory drawing so rotating balls never graze stationary hardware. Final load capacities, limiting rpm, and stamped steel, machined brass, or polymer cage specifications are issued on the verified ZQM print before order release.
2312 Cross-Reference & Heavy-Series Sleeve Check (H2312)
Pulp-and-paper reliability teams and woodyard maintenance planners comparing 60 × 130 × 46 mm spares should match both the 46 mm width and the dedicated H2312 heavy-width adapter sleeve:
| Brand / Standard | Cylindrical Bore | 1:12 Tapered Bore | Engineering Verification |
|---|---|---|---|
| ZQM Bearings | 2312 | 2312K | 46 mm width; ball-protrusion & cage verified on print |
| SKF | 2312 / 2312 M / 2312 E-2RS1TN9 | 2312 K / 2312 KM | M = machined brass cage; verify open vs sealed |
| FAG / Schaeffler | 2312-M / 2312-TVH | 2312-K-M / 2312-K-TVH | Confirm brass vs polymer cage for humid wet ends |
| NSK / NTN / KOYO | 2312 | 2312K | Verify H2312 sleeve compatibility & C3 clearance |
| Legacy GB Code | 1612 | 11612 | Historical Chinese Series 23 blueprint codes |
Interchange Boundary Statement: Equivalence listed above reflects ISO 15 boundary dimensions (60 × 130 × 46 mm) exclusively. Side-face ball protrusion dimensions, cage alloy, and internal capacities differ by manufacturer and must be verified on engineering drawings before installation.
Wet-End Corrosion Protection, Woodyard Seals & H2312 Assembly
In paper-mill wet sections and outdoor pulp, timber, and heavy process lines, acidic white-water spray and bark sap destroy unsealed steel surfaces rapidly. Pack split heavy pedestals with water-resistant calcium-sulfonate or lithium-complex grease and fit triple-barrier labyrinth flingers to deflect hose washdowns without adding drag torque to free-spinning felt rolls.
When clamping 2312K onto a 55 mm plain journal, strictly specify the wide H2312 adapter sleeve—an H312 sleeve built for 31 mm 1312K bearings is far too short to seat a 46 mm wide bore. Also recognize the heavy-shock boundary: while 2312 handles chipper feed rollers smoothly, the chipper’s primary knife-disc rotor shaft demands the extreme line-contact toughness of a 22312 spherical roller bearing.
Specifying 2312 & 2312K for Paper Mills & Wood-Processing OEMs
When sending your inquiry, clarify five points: bore style (60 mm straight 2312 or 2312K paired with H2312 sleeve), wet-end vs dry-end operating temperature and moisture exposure, retainer preference (machined brass, stamped steel, or polyamide), clearance class (CN or C3), and quantity. ZQM issues a signed engineering drawing confirming side-face clearance and rated capacities prior to manufacturing.
Request 2312 Factory Print & Technical Quote
2312 Engineering FAQ for Timber & Paper-Mill Reliability
Related Selection & Comparison: Compare slimmer 31 mm 1312 or 50 mm wide 2310, verify H2312 1:12 sleeve drive-up in our Tapered Bore Calculator, check M/TVH suffixes in the Bearing Suffix Decoder, or browse Self-Aligning Ball Bearings.
Why can’t an H312 adapter sleeve be used to mount a 2312K bearing?
The H312 sleeve is sized for the 31 mm wide 1312K. Because the heavy 2312K is 46 mm wide, it strictly requires the longer ISO 2982-1 H2312 adapter sleeve to engage the full 1:12 tapered bore on a 55 mm shaft.
Why must engineers check ball side-face protrusion on the 2312?
On wide Series 23 self-aligning ball bearings, the large double-row balls can project slightly past the nominal 46 mm ring faces, so adjacent spacer rings, lockwashers, and housing seals must have proper axial relief confirmed on the drawing.
Why do paper-mill felt-guide rolls prefer 2312 over a heavier roller bearing?
Unpowered felt-guide rolls are driven solely by friction from the moving fabric belt. The low rolling torque of the 2312 lets wide rolls turn freely without dragging or wearing expensive papermaking felts.
Which cage material works best for 2312 inside a humid paper-machine wet end?
Machined brass or stamped steel retainers are commonly preferred where warm water vapor, chemical washdowns, or higher dryer-section temperatures could age standard polyamide cages prematurely; confirm exact cage specs at quotation.
Where does a 22312 spherical roller bearing take over from 2312 on a wood chipper?
Use 2312 on hinged infeed pinch rolls requiring smooth alignment and moderate radial capacity, but specify 22312 spherical roller bearings (same 60 × 130 × 46 mm envelope) on heavy impact knife-disc shafts.



