51124 Thrust Ball Bearing 120 × 155 × 25 mm

Large-bore thin-section ISO 104 Series 11 single-direction flat-seat 51124 thrust ball bearing (120 × 155 × 25 mm, total height H = 25 mm, 17.5 mm radial wall), built for pipe-bending turntables and welding positioner swivel columns supporting slow intermittent axial deadweight (Fr = 0).

Request a Quote

The 51124 thrust ball bearing (120 × 155 × 25 mm, ISO 104 Dimension Series 11) surrounds a spacious 120 mm central bore with a remarkably trim 17.5 mm radial wall and 25 mm total height (H). Built for large-diameter pipe-bending turntables and welding positioner swivel columns, it supports slow intermittent axial deadweight smoothly while leaving the hollow 120 mm center wide open for hydraulic feed lines, purge-gas hoses, and rotary earthing assemblies. Like all ISO 104 flat-seat units, it takes strictly unidirectional pure axial load (Fr = 0) with no tapered-bore option.

ISO 104 Thin-Wall Attribute Code 51124 Nominal Spec Turntable / Positioner Notes
Shaft Washer Bore d 120 mm Clears large hollow swivel quill
Housing Washer OD D 155 mm Slim 17.5 mm single-side radial section
Assembled Stack Height H 25 mm Height H (not width B); low turntable base
Loading Constraint Unidirectional Axial Fr = 0 Only No radial support; zero overturning moment
Separable Washers 3-Piece Flat Seat Housing Bore D1 > 120 mm Verify bores carefully to avoid ring reversal
Axial Capacity & Cage Ca / C0a / Retainer Factory Drawing Verified Steel or brass cage & ratings confirmed at quote

51124 Large-Bore Thin Section on Pipe Benders & Welding Positioners

Fabrication shops bending heavy-wall process piping and welding pressure-vessel nozzles rely on wide hollow center columns to pass argon purge tubes, water-cooled torch utilities, and grounding copper shunts cleanly through the turntable centerline. Fitting a heavy-series 120 mm bearing would bloat pedestal casting diameters dramatically. By combining a 120 mm bore with a 155 mm OD and 25 mm height, the 51124 supports steady downward table and workpiece deadweight inside a compact base while keeping manual or geared swivel indexing effortless.

Fabrication engineers must enforce two critical operating guards around a 51124 column. First, because 51124 carries zero radial force (Fr = 0) and zero tilting moment, cantilevered pipe loads must be stabilized by widely spaced upper and lower radial guide bearings along the swivel mast, and the flat thrust seat must be precision-faced perpendicular to the mast axis. Second, on welding positioners, weld return current must bypass the 51124 via dedicated copper brush grounding blocks—stray arc current passing through ball-to-raceway contact points pits hardened steel into corrugated washboard fluting within hours. Confirmed static/dynamic axial ratings (C0a/Ca), steel vs brass cage options, and housing bore D1 are documented on the ZQM drawing upon quotation.

51124 Cross-Reference & Legacy 8124 Blueprint Mapping

Welding-equipment OEMs and pipe-shop maintenance departments matching ISO 104 Series 11 spares against legacy Chinese prints (8124) reference these nominal codes:

Manufacturer / Standard ISO 104 Base Code Shop Floor Verification
ZQM Bearings 51124 Print verifies D1 bore, steel/brass cage & C0a/Ca
SKF 51124 Flat-seat Series 11; confirm cage suffix (M/steel)
FAG / Schaeffler 51124 Verify washer flatness for wide 155 mm seat
NSK / NTN / KOYO 51124 Confirm static axial safety C0a for heavy spools
Legacy GB Code 8124 Classic Chinese fabrication-machinery code

Interchange Boundary: Matching 51124 across manufacturers establishes ISO 104 boundary equivalence (120 × 155 × 25 mm) strictly. Cage construction, washer heat treatment, and axial capacities C0a/Ca vary across makers and require blueprint verification before direct substitution.

Swivel Column Flatness, Washer Orientation & Arc-Current Isolation

Large thin-section rings measuring 120 × 155 mm deflect easily if dropped onto rough weldment plates inside heavy metalworking and steel fabrication shops. Always support the entire underside of the stationary housing washer on a stiff, surface-ground steel seat so thin washer walls never dish under heavy pipe spools.

During column assembly, distinguish the two rings immediately: seat the tight 120 mm shaft washer onto the rotating turntable flange and drop the slightly wider-bore housing washer (D1 > 120 mm) onto the stationary base pedestal—swapping them forces the stationary ring to scuff the rotating 120 mm column immediately. Seal the cavity with labyrinth shields against weld spatter and grinding grit, and if a positioner lifts upward as well as pushing downward, substitute a double-direction thrust series (522/523/524) or crossed-roller slewing ring.

Ordering 51124 Bearings for Fabrication Equipment OEMs & Overhauls

Include these operating details in your quote inquiry: static deadweight plus fixture mass, swivel rpm range, weld-grounding and spatter-shield layout, preferred pressed steel or machined brass retainer, and order quantity. ZQM engineering delivers a signed drawing with confirmed D1 clearance and axial C0a/Ca values before shipment.

Request 51124 Turntable Drawing & Quote

51124 Technical FAQ for Pipe Benders & Welding Positioners

Related Selection & Comparison: Compare 100 mm thin-wall 51120 (135 × 25 mm) or explore heavy crane thrust 51316 (80 × 140 × 44 mm), verify suffix codes in our Bearing Suffix Decoder, or browse Thrust Ball Bearings.

How do you protect a 51124 bearing from weld-current pitting on a welding positioner?

Install a dedicated low-resistance rotary copper grounding brush bypassing the swivel column, and insulate the bearing seat where needed so welding return amps never arc across the 51124 ball-to-raceway contacts.

How do installers verify the 51124 shaft washer versus housing washer before mounting?

Measure both inside diameters: the shaft washer matches the 120 mm nominal rotating column closely, whereas the housing washer has a larger bore (D1 > 120 mm) to clear the turning shaft cleanly.

Why does a 120 × 155 × 25 mm thin-section 51124 need stiff machined seating shoulders?

With a 17.5 mm radial wall around a 120 mm bore, uneven weldment bases distort the flat housing washer, concentrating axial deadweight on only a few balls and causing rapid spalling.

Can a 51124 alone hold an overhanging pipe bend that creates overturning moment?

No. The 51124 supports strictly pure vertical axial load (Fr = 0). Overturning moments and radial bending forces must be reacted by separate spaced radial bearings along the swivel column.

Is 51124 suitable for high-speed continuous rotation on a lathe spindle?

No. Large-diameter thrust ball bearings generate strong centrifugal ball forces at high rpm that trigger skidding; 51124 is intended strictly for slow intermittent swivel and turntable deadweight support.

Scroll to Top