The ZQM FCDP4872290/YA3 is a heavy-section, extra-wide pin-type four-row cylindrical roller bearing built for severe radial shock loads on heavy plate mills, hot strip roughing stands, and wide-strip steckel mills. Verified in ZQM’s factory catalogue (P097-R19-single) at 240 × 360 × 290 mm (Fw = 270 mm, mass 100.0 kg), its extra-wide 290 mm footprint and high roller fill deliver a massive 2,850 kN dynamic (Cr) and 5,670 kN static (C0r) capacity—nearly double the load rating of narrower 180 mm stands on the same 240 mm neck.
FCDP4872290/YA3 Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 240 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 360 mm |
| Boundary Dimensions & Weight | Width (B) | 290 mm |
| Boundary Dimensions & Weight | Roller set under-raceway diameter (Fw) | 270 mm |
| Boundary Dimensions & Weight | Catalogue diagram reference (fig) | 9 |
| Boundary Dimensions & Weight | Reference mass (Weight) | 100.0 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 2850 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 5670 kN |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 3.0 mm |
| Abutment & Fillet Dimensions | Minimum flange chamfer (r34) | 3.0 mm |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
FCDP Pin-Type Architecture for Shock-Loaded Plate & Roughing Mills
- Maximum Roller Count via Hollow-Roller Pin Cage: The
P(pin-type) construction passes hardened steel pins through centrally bored hollow rollers welded into end rings, allowing more rollers per row and dramatically higher fatigue capacity than comb-type cages under heavy slab entry shocks. - Split Outer Ring & Integral Rib Guidance (Figure 9): Engineered with robust outer-ring ribs and intermediate guide flanges to keep all four long roller rows aligned under severe roll bending deflection.
- Heavy Chamfer & Stress Relief (r12 = 3.0 mm): Generous
3.0 mmminimum chamfer accommodates larger roll-neck fillet radii to prevent shaft stress risers during heavy pass reductions. - Strict Fw = 270 mm Matched Verification: Confirm exact
Fw = 270 mmenvelope and internal radial clearance before pairing replacement inner rings with reconditioned mill chocks.
Nominal Rolling Mill Cross-Reference
| Brand / Series | Nominal Envelope Reference | Key Verification Point |
|---|---|---|
| ZQM Bearings | FCDP4872290/YA3 | 240 × 360 × 290 mm · Fw 270 mm · Pin-type Figure 9 |
| SKF / FAG / KOYO | 240×360×290 4RCRB Pin-Type | Confirm hollow-roller pin cage, Fw = 270 mm & YA3 lubrication |
Engineering Disclaimer: Cross-references indicate nominal boundary dimensions (240 × 360 × 290 mm) only. Always confirm Fw (270 mm), outer-ring oil groove alignment, and radial clearance class against your mill stand drawing.
Preventive Maintenance for Hot Strip & Plate Chocks
- Rotate the outer ring 90° inside the chock at scheduled campaign intervals to distribute the stationary heavy load zone across four fresh raceway quadrants.
- Check scale-water seals aggressively; ingress of hot mill cooling water rapidly degrades EP grease films in pin-cage roller bores.
- Record mounted radial clearance across rows 1 through 4 after each roll-neck regrind to detect uneven wear early.
Frequently Asked Questions — FCDP4872290/YA3
What advantage does the FCDP pin-type cage offer over standard FC comb cages?
Pin-type cages use hollow rollers threaded onto steel pins joined to end rings, eliminating bulky cage bars between rollers so more rollers fit in the same 240 × 360 × 290 mm envelope—boosting Cr to 2,850 kN and C0r to 5,670 kN.
What are the verified factory dimensions and mass of FCDP4872290/YA3?
Per ZQM catalogue record P097-R19-single: bore d = 240 mm, OD D = 360 mm, width B = 290 mm, roller-set Fw = 270 mm, chamfer r12 = 3.0 mm, dynamic load Cr = 2,850 kN, static load C0r = 5,670 kN, and weight 100.0 kg.
Why should rolling mill maintenance teams index the outer ring 90° during overhauls?
In roll-neck chocks the radial rolling force acts in a fixed vertical load zone. Indexing the outer ring 90° between campaigns brings fresh, unstressed raceway arcs into the primary load zone and substantially extends service life.
Can I mix an FCDP4872290/YA3 outer assembly with an older inner ring from another supplier?
Never mix sub-assemblies without verifying exact Fw (270 mm), inner-ring outer raceway diameter, chamfer clearance (3.0 mm), and four-row clearance uniformity on a calibrated gauge bench.
How can I obtain CMM inspection records and export lead times for FCDP4872290/YA3?
Submit your mill stand drawing, required radial clearance, and quantity via our Contact page for direct Wafangdian factory engineering support.





