The ZQM FCD5070230 is a precision twin-inner-ring (FCD) four-row cylindrical roller bearing designed for hot strip finishing stands, aluminum foil/sheet cold mills, and continuous tandem work rolls. Verified in ZQM’s factory catalogue (P097-R25-single) at 250 × 350 × 230 mm (Fw = 278 mm, mass 68.7 kg), its dual-inner-ring and dual-outer-ring Figure 4 layout delivers balanced radial load sharing of 1,900 kN dynamic (Cr) and 4,350 kN static (C0r) across all four roller rows.
FCD5070230 Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 250 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 350 mm |
| Boundary Dimensions & Weight | Width (B) | 230 mm |
| Boundary Dimensions & Weight | Roller set under-raceway diameter (Fw) | 278 mm |
| Boundary Dimensions & Weight | Catalogue diagram reference (fig) | 4 |
| Boundary Dimensions & Weight | Reference mass (Weight) | 68.7 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 1900 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 4350 kN |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 3.0 mm |
| Abutment & Fillet Dimensions | Minimum flange chamfer (r34) | 3.0 mm |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
FCD Twin-Ring Design Advantages for Continuous Strip Rolling
- Balanced Twin Inner & Outer Rings (Figure 4): Splitting the 230 mm bearing width into two matched twin-row inner rings and two outer rings improves axial clamping uniformity and simplifies roll-shop induction mounting on 250 mm journals.
- High-Speed Thermal Stability for Strip & Foil Mills: The
250 × 350 × 230 mmgeometry balances radial stiffness with lower friction torque than heavier 290 mm roughing units, reducing strip gauge variation caused by thermal neck growth. - Verified Roller Envelope (Fw = 278 mm): Factory-matched to
Fw = 278 mmwithr12 = 3.0 mmchamfers; preserve serialized ring pairing during roll-shop teardowns to maintain uniform radial clearance. - Direct Sibling Lineage to ZQM FCD5678275: Shares the proven FCD metallurgical and grinding control protocol trusted by export steel and non-ferrous rolling plants.
Nominal Rolling Mill Cross-Reference
| Manufacturer | Nominal Designation | Dimension & Fit Scope |
|---|---|---|
| ZQM Bearings | FCD5070230 | 250 × 350 × 230 mm · Fw 278 mm · Twin-inner Figure 4 |
| NTN / NSK / KOYO | 250×350×230 4R-CRB (FCD series) | Nominal ISO mill envelope; confirm Fw = 278 mm & oil ports |
Engineering Disclaimer: Cross-references are for nominal boundary dimension comparison (250 × 350 × 230 mm) only. Confirm exact Fw (278 mm), internal clearance, and lubrication groove geometry against your mill chock drawing prior to replacement.
Roll-Shop Inspection Routine for FCD5070230 Sets
- Keep both twin inner rings and both outer rings serialized together—re-install matching face marks in their factory sequence.
- Check neck interference fit (typically ISO n6/p6 for high-speed strip work rolls) so inner rings do not creep under reversing rolling torque.
- Inspect all four roller rows for micro-pitting and verify clean drainage of roll-coolant emulsions away from chock seals.
Frequently Asked Questions — FCD5070230
What does the D in FCD5070230 signify compared to FC series?
FCD denotes a four-row cylindrical roller bearing utilizing double (twin) inner rings and double outer rings (Figure 4), simplifying roll-neck heating/mounting and promoting balanced clamping across the 230 mm width.
What are the exact catalogue dimensions and load ratings of FCD5070230?
Per ZQM catalogue record P097-R25-single: bore d = 250 mm, OD D = 350 mm, width B = 230 mm, Fw = 278 mm, chamfer r12 = 3.0 mm, dynamic load Cr = 1,900 kN, static load C0r = 4,350 kN, and reference mass 68.7 kg.
Is FCD5070230 suitable for aluminum cold rolling as well as steel hot strip finishing?
Yes. Its 250 × 350 × 230 mm twin-ring geometry is widely used in both steel hot strip finishing stands and non-ferrous aluminum sheet/foil cold mills where low radial runout controls strip thickness tolerance.
Can ZQM supply FCD5070230 to tighter P6 or P5 running accuracy?
Yes. Higher running accuracy grades (such as P6 or P5 per ISO 492) and tailored radial clearance groups for high-speed cold mills are manufactured and CMM-inspected strictly per confirmed engineering drawings.
How can mills order matched sets of FCD5070230 from ZQM?
Reach out via our Contact page with required quantity, tolerance grade, clearance group, and chock drawing for direct factory quotation.






