FCDP4872290/YA3 Four-Row Cylindrical Roller Bearing 240 × 360 × 290 mm

ZQM FCDP4872290/YA3 Pin-Type Four-Row Cylindrical Roller Bearing (240 × 360 × 290 mm, Fw 270 mm, Cr 2,850 kN, C0r 5,670 kN, 100.0 kg) engineered for extreme rolling forces in heavy plate and hot strip mills.

SKU: FCDP4872290YA3 Category:

Request a Quote

The ZQM FCDP4872290/YA3 is a heavy-section, extra-wide pin-type four-row cylindrical roller bearing built for severe radial shock loads on heavy plate mills, hot strip roughing stands, and wide-strip steckel mills. Verified in ZQM’s factory catalogue (P097-R19-single) at 240 × 360 × 290 mm (Fw = 270 mm, mass 100.0 kg), its extra-wide 290 mm footprint and high roller fill deliver a massive 2,850 kN dynamic (Cr) and 5,670 kN static (C0r) capacity—nearly double the load rating of narrower 180 mm stands on the same 240 mm neck.

FCDP4872290/YA3 Technical Specifications & Dimensions

Data Source: ZQM Factory PDF Catalogue DB (v1)Status: Catalogue Reference ValuesCatalogue Ref: FCDP4872290/YA3
Parameter CategoryTechnical Parameter (Symbol)Catalogue Reference Value
Boundary Dimensions & WeightBore diameter (d)240 mm
Boundary Dimensions & WeightOutside diameter (D)360 mm
Boundary Dimensions & WeightWidth (B)290 mm
Boundary Dimensions & WeightRoller set under-raceway diameter (Fw)270 mm
Boundary Dimensions & WeightCatalogue diagram reference (fig)9
Boundary Dimensions & WeightReference mass (Weight)100.0 kg
Load Ratings & Limiting SpeedsBasic dynamic load rating (Cr)2850 kN
Load Ratings & Limiting SpeedsBasic static load rating (Cor)5670 kN
Abutment & Fillet DimensionsMinimum chamfer dimension (r12)3.0 mm
Abutment & Fillet DimensionsMinimum flange chamfer (r34)3.0 mm

Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.

FCDP Pin-Type Architecture for Shock-Loaded Plate & Roughing Mills

  • Maximum Roller Count via Hollow-Roller Pin Cage: The P (pin-type) construction passes hardened steel pins through centrally bored hollow rollers welded into end rings, allowing more rollers per row and dramatically higher fatigue capacity than comb-type cages under heavy slab entry shocks.
  • Split Outer Ring & Integral Rib Guidance (Figure 9): Engineered with robust outer-ring ribs and intermediate guide flanges to keep all four long roller rows aligned under severe roll bending deflection.
  • Heavy Chamfer & Stress Relief (r12 = 3.0 mm): Generous 3.0 mm minimum chamfer accommodates larger roll-neck fillet radii to prevent shaft stress risers during heavy pass reductions.
  • Strict Fw = 270 mm Matched Verification: Confirm exact Fw = 270 mm envelope and internal radial clearance before pairing replacement inner rings with reconditioned mill chocks.

Nominal Rolling Mill Cross-Reference

Brand / Series Nominal Envelope Reference Key Verification Point
ZQM Bearings FCDP4872290/YA3 240 × 360 × 290 mm · Fw 270 mm · Pin-type Figure 9
SKF / FAG / KOYO 240×360×290 4RCRB Pin-Type Confirm hollow-roller pin cage, Fw = 270 mm & YA3 lubrication

Engineering Disclaimer: Cross-references indicate nominal boundary dimensions (240 × 360 × 290 mm) only. Always confirm Fw (270 mm), outer-ring oil groove alignment, and radial clearance class against your mill stand drawing.

Preventive Maintenance for Hot Strip & Plate Chocks

  1. Rotate the outer ring 90° inside the chock at scheduled campaign intervals to distribute the stationary heavy load zone across four fresh raceway quadrants.
  2. Check scale-water seals aggressively; ingress of hot mill cooling water rapidly degrades EP grease films in pin-cage roller bores.
  3. Record mounted radial clearance across rows 1 through 4 after each roll-neck regrind to detect uneven wear early.

Frequently Asked Questions — FCDP4872290/YA3

What advantage does the FCDP pin-type cage offer over standard FC comb cages?

Pin-type cages use hollow rollers threaded onto steel pins joined to end rings, eliminating bulky cage bars between rollers so more rollers fit in the same 240 × 360 × 290 mm envelope—boosting Cr to 2,850 kN and C0r to 5,670 kN.

What are the verified factory dimensions and mass of FCDP4872290/YA3?

Per ZQM catalogue record P097-R19-single: bore d = 240 mm, OD D = 360 mm, width B = 290 mm, roller-set Fw = 270 mm, chamfer r12 = 3.0 mm, dynamic load Cr = 2,850 kN, static load C0r = 5,670 kN, and weight 100.0 kg.

Why should rolling mill maintenance teams index the outer ring 90° during overhauls?

In roll-neck chocks the radial rolling force acts in a fixed vertical load zone. Indexing the outer ring 90° between campaigns brings fresh, unstressed raceway arcs into the primary load zone and substantially extends service life.

Can I mix an FCDP4872290/YA3 outer assembly with an older inner ring from another supplier?

Never mix sub-assemblies without verifying exact Fw (270 mm), inner-ring outer raceway diameter, chamfer clearance (3.0 mm), and four-row clearance uniformity on a calibrated gauge bench.

How can I obtain CMM inspection records and export lead times for FCDP4872290/YA3?

Submit your mill stand drawing, required radial clearance, and quantity via our Contact page for direct Wafangdian factory engineering support.

Scroll to Top