FC4866180/YA4 Four-Row Cylindrical Roller Bearing 240 × 330 × 180 mm

ZQM FC4866180/YA4 Four-Row Cylindrical Roller Bearing (240 × 330 × 180 mm, Fw 265 mm, Cr 1,460 kN, C0r 3,490 kN, 49.5 kg) for high-speed wire rod and bar finishing mill work rolls.

SKU: FC4866180YA4 Category:

Request a Quote

The ZQM FC4866180/YA4 is a compact-section four-row cylindrical roller bearing engineered specifically for high-speed wire rod and bar finishing stand work rolls. Built to verified factory catalogue dimensions of 240 × 330 × 180 mm (Fw = 265 mm, reference mass 49.5 kg), its slim radial wall thickness (45 mm) maximizes roll-neck diameter strength inside narrow merchant-bar chocks while delivering 1,460 kN dynamic (Cr) and 3,490 kN static (C0r) radial capacity.

FC4866180/YA4 Technical Specifications & Dimensions

Data Source: ZQM Factory PDF Catalogue DB (v1)Status: Catalogue Reference ValuesCatalogue Ref: FC4866180/YA4
Parameter CategoryTechnical Parameter (Symbol)Catalogue Reference Value
Boundary Dimensions & WeightBore diameter (d)240 mm
Boundary Dimensions & WeightOutside diameter (D)330 mm
Boundary Dimensions & WeightWidth (B)180 mm
Boundary Dimensions & WeightRoller set under-raceway diameter (Fw)265 mm
Boundary Dimensions & WeightCatalogue diagram reference (fig)1
Boundary Dimensions & WeightReference mass (Weight)49.5 kg
Load Ratings & Limiting SpeedsBasic dynamic load rating (Cr)1460 kN
Load Ratings & Limiting SpeedsBasic static load rating (Cor)3490 kN
Abutment & Fillet DimensionsMinimum chamfer dimension (r12)2.1 mm
Abutment & Fillet DimensionsMinimum flange chamfer (r34)2.1 mm

Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.

Why Bar & Wire Rod Finishing Stands Specify FC4866180/YA4

  • Slim-Wall Roll-Neck Optimization: With a compact 240 mm bore to 330 mm outside diameter ratio, FC4866180/YA4 preserves neck bending stiffness during rapid multi-pass billet reductions.
  • YA4 Lubrication & Separable Roll-Change Efficiency: Figure 1 separable inner-ring architecture lets steel mill crews leave inner rings shrunk onto work roll necks while swapping pre-assembled chocks during fast pass changes.
  • Mandatory Fw Envelope Discipline (265 mm): Every FC4866180/YA4 bearing is ground to a verified roller-set bore diameter Fw = 265 mm. Never interchange inner rings across different serial batches without verifying measured Fw and mounted radial clearance on all four roller rows.
  • Pure Radial Load Architecture: Carries radial separating forces exclusively; pair with an adjacent bidirectional locating bearing (such as a QJF four-point contact ball or double-row tapered thrust unit) to control axial roll float.

Nominal ISO / Rolling Mill Cross-Reference

Brand / System Nominal Reference Engineering Notes
ZQM Bearings FC4866180/YA4 240 × 330 × 180 mm · Fw 265 mm · Figure 1
SKF 313824 / 314553 series envelope Verify exact Fw and lubrication groove pattern by drawing
FAG / NSK 240×330×180 4RCRB envelope Nominal boundary reference only; check Fw = 265 mm

Engineering Disclaimer: Nominal boundary references compare d × D × B envelopes only and do not guarantee direct sub-assembly interchangeability. Always confirm Fw (265 mm), radial clearance group, and oil/mist lubrication ports against your chock drawing.

Mounting & Lubrication Checklist for Wire Rod Mill Crews

  1. Inspect work-roll neck taper/cylindricity and verify shaft shoulder fillet radius remains strictly smaller than chamfer r12 min = 2.1 mm (e.g., ra max ≤ 2.0 mm).
  2. Heat the separable inner ring inductively (typically ≤ 110 °C) for interference seating against the roll shoulder, then re-verify mounted outer raceway diameter before sliding into the chock.
  3. Verify radial clearance across all four roller rows with feeler gauges and confirm clean oil-air or circulating oil delivery through outer-ring lubrication grooves.

Frequently Asked Questions — FC4866180/YA4

What are the verified dimensions and Fw diameter of FC4866180/YA4?

Per ZQM catalogue record P097-R10-single, FC4866180/YA4 measures 240 mm bore (d) × 330 mm OD (D) × 180 mm width (B), with roller-set envelope Fw = 265 mm, chamfer r12 = 2.1 mm, Cr = 1,460 kN, C0r = 3,490 kN, and mass 49.5 kg.

Why must Fw = 265 mm be verified before swapping work rolls between chocks?

Even small deviations in inner-ring raceway OD or outer roller envelope Fw alter mounted radial clearance across the four rows, risking thermal seizure or premature spalling in high-speed finishing stands.

Can FC4866180/YA4 take axial roll thrust on its own?

No. Four-row cylindrical roller bearings carry pure radial rolling load; axial roll positioning must be handled by a dedicated thrust or four-point contact locating bearing mounted outside the chock.

What lubrication systems work best for FC4866180/YA4 finishing stands?

High-speed wire rod and merchant bar mills typically deploy oil-air mist or filtered circulating oil lubrication fed through the outer ring groove and oil holes to control temperature rise.

How can steel plants request factory pricing and inspection reports for FC4866180/YA4?

Send your annual mill consumption, clearance group, and chock drawing via our Contact page to receive factory pricing and inspection specifications within 24 hours.

Scroll to Top