,

6224 Deep Groove Ball Bearing 120 × 215 × 40 mm

Medium ISO 62-series 6224 deep groove ball bearing (120 × 215 × 40 mm, 5.26 kg) rated at 145 kN dynamic and 118 kN static radial capacity for V-belt driven Roots positive-displacement blowers and rotary screw air ends.

Request a Quote

Inside an industrial wastewater aeration Roots blower or pneumatic-conveying rotary lobe compressor, twin counter-rotating rotors maintain razor-thin micron clearances against the cast housing while absorbing steady differential air-pressure pulsations and heavy V-belt drive tension. Measuring 120 × 215 × 40 mm at 5.26 kg, the ZQM 6224 deep groove ball bearing hits the medium ISO 62-series engineering sweet spot: 145 kN dynamic capacity (Cr), 118 kN static rating (C0r), and 2,800 rpm grease / 3,400 rpm oil speed limits that keep blower rotors aligned cleanly.

6224 Technical Specifications & Dimensions

Data Source: ZQM Factory PDF Catalogue DB (v1)Status: Catalogue Reference ValuesCatalogue Ref: 6224
Parameter CategoryTechnical Parameter (Symbol)Catalogue Reference Value
Boundary Dimensions & WeightBore diameter (d)120 mm
Boundary Dimensions & WeightOutside diameter (D)215 mm
Boundary Dimensions & WeightWidth (B)40 mm
Boundary Dimensions & WeightReference mass (Weight)5.26 kg
Load Ratings & Limiting SpeedsBasic dynamic load rating (Cr)145 kN
Load Ratings & Limiting SpeedsBasic static load rating (Cor)118 kN
Load Ratings & Limiting SpeedsLimiting speed (grease)2800 rpm
Load Ratings & Limiting SpeedsLimiting speed (oil)3400 rpm
Abutment & Fillet DimensionsShaft abutment diameter (da)131 mm
Abutment & Fillet DimensionsHousing abutment diameter (Da)204 mm
Abutment & Fillet DimensionsMinimum chamfer dimension (r12)2.1 mm
Abutment & Fillet DimensionsMaximum fillet radius (ra)2 mm
Calculation FactorsCalculation factor (f0)14

Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.

Medium 62-Series Advantages in Positive-Displacement Blowers

Twin-lobe and tri-lobe rotary blowers cannot accommodate oversized 63-series outer rings because parallel rotor shaft centerlines sit closely together—making the 6224’s 215 mm outer diameter indispensable:

  • Balanced Belt-Pull & Centerline Packaging: Packing 145 kN dynamic endurance into a 215 mm OD lets designers run multi-band V-belt sheaves directly off the 120 mm drive shaft without colliding with the adjacent driven-lobe bearing bore.
  • Micron Lobe-Clearance Axial Control (f0 = 14): On the fixed timing-gear end, the 6224’s deep groove geometry holds rotor end-face clearances to tight tolerances against pulsing discharge pressure, sized via calculation factor f0 = 14.
  • Dual-End Lubrication Versatility: Roots blowers commonly oil-splash the timing-gear housing (up to 3,400 rpm oil rating) while grease-lubricating the drive-end headplate (up to 2,800 rpm grease rating)—allowing the same 6224 envelope to serve cleanly across diverse compressor layouts.
  • Low Pulsation Noise Floor: Precision ball sphericity and smooth raceway honing curb bearing-induced acoustic rumble in continuous 24/7 municipal aeration plants.

ISO 15 Cross-Reference Guide for 6224

Maker Model Code d (mm) D (mm) B (mm) Blower & Compressor Variants
ZQM 6224 120 215 40 Open medium-series catalog base; C3/cage per order
SKF 6224 / 6224/C3 120 215 40 Explorer low-noise steel or brass cage
FAG / Schaeffler 6224 / 6224-C3 120 215 40 High-load Generation C geometry
NSK / NTN 6224 / 6224C3 120 215 40 Available open, shielded ZZ, or sealed 2RS
Koyo / JTEKT 6224 120 215 40 Industrial blower & compressor medium series

Technical cross-reference disclaimer: Designations match strictly on ISO 15 external dimensions (120 × 215 × 40 mm). Radial internal clearance (especially C3 for hot compressed-air discharge ends), cage material, and synthetic oil compatibility vary by maker—verify against blower service manuals before installation.

Roots Blower & Screw Air End 6224 Maintenance Playbook

  • Verify Side-Plate Abutment Geometry: Machine shaft shoulders to da ≥ 131 mm and headplate bore abutments to Da ≤ 204 mm, holding corner fillets to ra ≤ 2 mm to clear the 2.1 mm minimum chamfer cleanly.
  • Stop Over-Greasing on Drive-End Headplates: Blower discharge temperatures routinely heat headplates to 85–105 °C. Pumping excess grease into a 2,200 rpm 6224 traps churning heat, oxidizes thickeners, and blows past piston-ring oil seals into the clean aeration air stream. Follow measured-gram relubrication schedules using high-temp synthetic polyurea or lithium-complex grease with exit purge plugs removed.
  • Specify C3 Clearance for Hot Discharge Rotors: Thermal growth of the 120 mm steel rotor shaft inside a hot compression chamber narrows operating radial clearance; confirm whether your OEM calls for C3 clearance before mounting standard CN stock.
  • Dial-Check V-Belt Tension & Sheave Overhang: Mount the drive pulley as close to the 6224 centerline as guarding allows and use a tension meter—over-tightened belts silently double radial load and slash fatigue life by a factor of eight.

Stocking overhaul kits for wastewater Roots blowers, pneumatic grain-handling compressors, or rotary screw air ends? Connect with our ZQM blower & compressor bearing team for C3 stock checks and multi-unit pricing.

Roots Blower & Screw Air End 6224 Engineering FAQ

Related Selection & Comparison: Under heavier shock loads on a 120 mm shaft, evaluate the deep-section 6324 bearing (260 × 55 mm), check industrial blower setups in Industrial Gearboxes & Drives, or browse Deep Groove Ball Bearings.

Why do Roots blowers use 6224 instead of the heavier 6324 on a 120 mm rotor shaft?

Twin-lobe blower shafts run side by side at fixed gear center distances. A 6324’s 260 mm OD frequently overlaps the neighboring bore, whereas the 6224 fits inside a 215 mm OD while still providing 145 kN dynamic radial capacity.

What causes drive-end 6224 grease to darken and harden inside an aeration blower?

Two culprits dominate: radiant heat from high-pressure air discharge above 95 °C and over-greasing during routine PM rounds. Switching to synthetic high-temperature grease, respecting exact gram-per-interval doses, and purging old grease eliminates thermal coking.

Can an open 6224 run in the splash-oil timing gear case of a rotary blower?

Yes—open 6224 bearings are designed for oil-splash and circulating oil lubrication up to 3,400 rpm. Ensure gear-case oil (typically ISO VG 150–220 synthetic) stays free of bronze gear wear debris via regular oil changes.

How sensitive is the 6224 to excessive V-belt tension on a belt-driven blower?

Because ball-bearing fatigue life scales inversely with the cube of radial load, cranking V-belt tension 40% above specification cuts L10h life by more than half while elevating housing temperature noticeably.

Scroll to Top