QJF1048X1MB Four-Point Contact Ball Bearing Overview
Engineered with a non-standard outer diameter of 359.5 mm (0.5 mm smaller than standard integer 360 mm QJ 1048 bearings), the QJF1048X1MB single-row four-point contact ball bearing (240 × 359.5 × 56 mm, reference mass 20.9 kg) handles bidirectional axial thrust in compact rolling mill chocks, heavy compressors, and gearbox locating stacks. Per ZQM Bearings’ 259-page general catalogue, it delivers a basic dynamic load rating Cr of 449 kN and basic static load rating C0r of 780 kN.
Critical Housing Fit Alert (-0.5 mm Special OD): The 359.5 mm outer diameter is intentionally undersized relative to a nominal 360 mm housing bore so the outer ring remains radially free (floating) and carries pure bidirectional axial load while an adjacent radial roller bearing supports 100% of radial force. Always verify housing bore dimensions and tolerances against your equipment drawing before ordering.
QJF1048X1MB Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 240 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 359.5 mm |
| Boundary Dimensions & Weight | Width (B) | 56 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 20.9 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 449 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 780 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 1200 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 1700 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 254 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 346 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 3.0 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 2.5 mm |
| Abutment & Fillet Dimensions | Load center distance (a) | 210 mm |
| Calculation Factors | Calculation factor (e) | 0.95 |
| Calculation Factors | Axial load factor (static) (Y0) | 0.58 |
| Calculation Factors | Axial load factor (Y1) | 0.66 |
| Calculation Factors | Axial load factor (Y2) | 1.07 |
| Calculation Factors | Radial load factor (X) | 0.6 |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
Structural Design and Axial Locating Engineering
- 35° Contact Angle & Split-Ring Architecture: Accommodates heavy reversing axial loads in both directions within a single 56 mm axial width (load center a = 210 mm), replacing back-to-back paired angular contact bearings where axial space is restricted.
- Cylindrical Bore (Non-Tapered): Manufactured with a straight 240 mm cylindrical bore; standard QJF bearings do not use tapered K sleeves.
- Machined Solid Cage (MB): Inner-ring guided machined solid cage construction suited for sustained industrial speeds (reference grease limit 1,200 r/min, oil limit 1,700 r/min); exact cage alloy and tolerance class are confirmed on the order drawing.
Typical Industrial Equipment Applications
- Steel Rolling Mill Locating Stacks: Paired beside four-row cylindrical rolling mill bearings (Steel and Rolling Mills Hub) to take pure bidirectional axial thrust.
- Heavy Helical Gearboxes & Compressors: High-speed input and intermediate shaft axial locating positions where radial loads are carried by adjacent NU/NJ cylindrical roller bearings.
- Large Vertical Pumps & Rotary Drives: Compact axial thrust control under reversing operating cycles.
ISO Nominal Cross-Reference for QJF1048X1MB
| Brand | Nominal Series Reference | Critical OD Check | Engineering Note |
|---|---|---|---|
| ZQM Bearings | QJF1048X1MB | 359.5 mm (-0.5 mm special OD) | Verified in ZQM 259-page General Catalogue |
| Standard ISO Series | QJ 1048 / QJF 10.. | 360 mm (standard integer OD) | NOT directly interchangeable on housing fit without verifying 359.5 vs 360 mm bore |
ISO Nominal Boundary Disclaimer: Cross-brand references indicate nominal bore/width series alignment only and do not promise drop-in interchangeability. Always confirm outer diameter (359.5 mm vs 360 mm), axial internal clearance, and housing drawings prior to replacement.
Mounting Abutment and Lubrication Guidelines
Verify shaft shoulder diameter da min = 254 mm, housing shoulder diameter Da max = 346 mm, and maximum fillet radius ra max = 2.5 mm. Ensure the outer ring is clamped axially with proper anti-rotation pin or radial clearance so it does not experience radial preloading. For speed-load evaluation, run your duty cycle in our ISO 281 Bearing Life Calculator or verify nomenclature in our Bearing Suffix Decoder.
Factory Quality Control and Export Supply
Manufactured at Wafangdian Qunma Bearing Manufacturing Co., Ltd. (ISO 9001 & ISO 14001 certified) with Ningbo export engineering support and Shanghai consolidation. Actual supplied clearance, tolerance class, and inspection documentation are confirmed in writing before production. Contact ZQM Bearings for drawing review and factory quotation.
Frequently Asked Questions — QJF1048X1MB
Why does QJF1048X1MB have a 359.5 mm outer diameter instead of 360 mm?
The 359.5 mm outer diameter is 0.5 mm smaller than the standard 360 mm QJ 1048 OD so the bearing sits radially free inside a nominal 360 mm housing bore. This prevents radial load from transferring into the four-point contact ball bearing when paired alongside a radial roller bearing.
Can I replace a 360 mm QJ 1048 directly with QJF1048X1MB (359.5 mm)?
Only if your equipment drawing specifies a radially floating 359.5 mm outer ring inside a 360 mm housing. Never substitute between 359.5 mm and 360 mm outer diameters without checking the housing bore tolerance and anti-rotation locking design.
What are the verified load ratings and weight of QJF1048X1MB?
Per ZQM Bearings’ catalog database, QJF1048X1MB (240 × 359.5 × 56 mm) has a basic dynamic load rating Cr of 449 kN, basic static load rating C0r of 780 kN, reference mass of 20.9 kg, and limiting speeds of 1,200 r/min (grease) / 1,700 r/min (oil).
Does QJF1048X1MB have a tapered bore?
No. QJF1048X1MB has a standard 240 mm straight cylindrical bore and does not mount on tapered K or K30 adapter sleeves.
What details should I send to quote QJF1048X1MB?
Provide designation QJF1048X1MB, confirm whether you require the 359.5 mm special OD (or standard 360 mm), specify clearance and quantity, and share your destination port via our Contact page.



