The ZQM LM277149DA/LM277110/LM277110D is a standard inch-series four-row tapered roller bearing (TQO Design 1) built for North American, European, and global hot/cold strip rolling mill roll-necks. Verified in ZQM’s factory catalogue (P236-R21-single) at exact inch-converted boundary dimensions of 558.8 × 736.6 × 457.2 mm (22.0000″ × 29.0000″ × 18.0000″, reference mass 525 kg), this matched assembly sustains combined radial separating forces and bidirectional axial roll thrust inside a single chock.
LM277149DA/LM277110/LM277110D Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 558.8 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 736.6 mm |
| Boundary Dimensions & Weight | Overall width (T) | 457.2 mm |
| Boundary Dimensions & Weight | Catalogue design designation (design) | 1 |
| Boundary Dimensions & Weight | Reference mass (Weight) | 525 kg |
| Calculation Factors | Calculation factor (e) | 0.33 |
| Calculation Factors | Axial geometry factor (K) | 1.77 |
| Calculation Factors | Axial load factor (static) (Y0) | 1.98 |
| Calculation Factors | Axial load factor (Y1) | 2.03 |
| Calculation Factors | Axial load factor (Y2) | 3.02 |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
Inch-Series TQO Design Highlights for Strip Mill Roll-Necks
- Complete Matched 4-Row Assembly: Comprises two double-row cones (
LM277149DA), two single outer cups (LM277110), one double outer cup (LM277110D), and precision-ground intermediate cone and cup spacer rings. - Verified Axial Load Calculation Factors: Catalogue-verified geometry factors
e = 0.33,Y1 = 2.03,Y2 = 3.02,Y0 = 1.98, andK = 1.77support accurate combined equivalent-load engineering calculations. - Factory-Set Bench Endplay (BEN) via Matched Spacers: Axial clearance is permanently set by factory-ground serialized spacers—never apply radial feeler-gauge methods, and never mix cones, cups, or spacers across different serial numbers.
- Drawing-Confirmed Load & Groove Options: Dynamic/static load ratings, helical inner-bore grease grooves (for loose roll-neck slip fits), and optional integrated roll-neck seals are confirmed directly against your mill drawing.
Nominal Inch-Series Mill Cross-Reference
| System | Nominal Assembly Designation | Boundary Envelope |
|---|---|---|
| ZQM Bearings | LM277149DA/LM277110/LM277110D | 558.8 × 736.6 × 457.2 mm (22″ × 29″ × 18″) · 525 kg |
| Timken / ABMA Inch System | LM277149DA-902A1 / LM277110 / LM277110D | Nominal inch TQO envelope; verify spacer BEN & bore grooves |
Engineering Disclaimer: Cross-references compare nominal inch boundary dimensions (22.0000″ × 29.0000″ × 18.0000″) only. Confirm exact spacer code, bench endplay (BEN), lubrication slots, and seal configuration against engineering drawings before installation.
Chock Assembly & Spacer Integrity Rules
- Verify serial numbers stamped on both
LM277149DAcones, cups, and cone/cup spacers match as one complete set before lowering into the chock. - Confirm chock end-cover clamp force seats the outer cups solidly against the chock shoulder without compressing spacer clearance.
- Inspect inner-bore lubrication grooves (if loose-fitted on the roll neck) during every roll change to prevent fretting corrosion on the 22-inch journal.
Frequently Asked Questions — LM277149DA/LM277110/LM277110D
What are the exact metric and inch dimensions of LM277149DA/LM277110/LM277110D?
Per ZQM catalogue P236-R21-single, bore d = 558.8 mm (22.0000 in), outside diameter D = 736.6 mm (29.0000 in), overall width T = 457.2 mm (18.0000 in), and reference mass is 525 kg.
How is internal clearance adjusted on this four-row tapered roller bearing?
Internal axial clearance (BEN / bench endplay) is pre-established at the factory through matched precision-ground inner and outer spacer rings. Never adjust clearance with radial feeler gauges or swap spacers between assemblies.
Why are dynamic and static load ratings confirmed per drawing for P236 TQO listings?
Because ZQM strictly publishes only printed factory catalogue figures, and PDF page 236 lists geometry, mass (525 kg), and axial factors (e = 0.33, Y1 = 2.03, Y2 = 3.02, K = 1.77), exact dynamic/static load ratings are confirmed by our engineering department according to your steel grade and cage specification.
Can ZQM supply helical inner-bore grease grooves for loose-fitted roll necks?
Yes. Loose-fitted mill roll necks commonly specify helical bore grooves and face lubrication slots to prevent neck scuffing; confirm groove geometry on your drawing at quotation stage.
How do North American or European steel mills request quotes for LM277149DA assemblies?
Send your full assembly code, desired bench endplay (BEN), seal requirement, and delivery port via our Contact page for 24-hour export engineering response.



