Construction Machinery & Heavy Vehicles

Construction Machinery and Heavy Vehicle Bearings

Built for excavators, wheel loaders, bulldozers, articulated haul trucks, and vibratory compactors working under severe shock loads and abrasive jobsite dust. ZQM supplies ISO 355 tapered roller (302 / 322 / 323 / 331), full-complement NCF / NNCF / NNCL, and heavy NJ / NU & 222 / 223 roller bearings.

1,067+Metric & Inch Tapered Models in DB
314+Full-Complement NCF / NNCF / NNCL Units
100–140 mmFeatured Heavy Drivetrain Bore Focus
ISO 355 / 15Tapered Overall T & Radial Compliance

Bearing Selection by Construction Equipment Assembly

Match heavy-duty earthmoving axles, planetary travel drives, powershift transmissions, and vibratory drums to verified ZQM roller bearing series.

Heavy metric tapered roller bearing representative image for wheel loader and dump truck axles
Axle Hubs & Bevel Differentials

Wheel Loader, Bulldozer & Heavy Truck Axles

Opposed pairs of 302, 322, and heavy 323 metric tapered roller bearings carry simultaneous vehicle weight, cornering thrust, and bevel-gear separating forces inside wheel hubs and differential carriers per ISO 355.

NCF full-complement cageless cylindrical roller bearing cross-section for excavator planetary travel drives
Planetary Final & Travel Drives

Excavator Travel Reductions & Track Drives

Compact crawler final drives and planetary pinions demand maximum radial static and shock capacity at low rotational speed. Single-row NCF and double-row NNCF / NNCL full-complement cylindrical bearings deliver dense roller complement without cage radial space loss.

Compact high-capacity tapered roller bearing representative image for powershift transmissions
Transmissions & Transfer Cases

Powershift Gearboxes & Hydraulic Drive Shafts

High-torque powershift shafts and transfer boxes combine compact wide 331 tapered roller bearings with separable straight-bore NJ (one-direction locating) and NU (non-locating floating) brass-caged cylindrical roller bearings.

Heavy-duty spherical roller bearing representative image for vibratory compactors and articulated haulers
Vibratory Drums & Heavy Chassis

Vibratory Compactors, Articulated Haulers & Booms

Eccentric vibratory road-roller drums and articulated dump-truck chassis pivots face severe cyclic vibration and housing misalignment. Heavy 223, 222, and 232 CA/W33 spherical roller bearings with C3/C4 clearance sustain continuous impact.

Verified Construction Machinery & Drivetrain Reference Bearings

Verified Specifications · ZQM Engineering Catalogue
Model Series / Design Dimensions (d × D × B/T) Basic Load Cr / C0r Ref. Mass Typical Construction Assembly Datasheet
32324 Heavy Tapered (323, C=69 mm) 120 × 260 × 90.5 mm (T) 770 / 1,060 kN 21.8 kg Heavy mining/haul truck axle & bevel drive View Spec
32224 Medium-Heavy Tapered (322, C=50) 120 × 215 × 61.5 mm (T) 440 / 635 kN 9.00 kg Wheel loader hubs & differential pinions View Spec
30224 Standard Tapered (302, C=34) 120 × 215 × 43.5 mm (T) 335 / 450 kN 6.28 kg Heavy vehicle axle hubs & gearbox shafts View Spec
33120 Compact Wide Tapered (331, C=40) 100 × 165 × 52 mm (T) 325 / 523 kN 4.29 kg Powershift transmissions & compact hubs View Spec
NCF3028V Single-Row Full-Complement (NCF) 140 × 210 × 53 mm 468 / 750 kN 6.10 kg Excavator planetary travel reductions Catalog
NNCF5022V Double-Row Full-Complement (NNCF) 110 × 170 × 80 mm 528 / 930 kN 6.60 kg High-shock crawler drives & boom sheaves Catalog
NNCL4922V Double-Row Floating (NNCL) 110 × 150 × 40 mm 201 / 430 kN 2.15 kg Compact planetary gears & winch drums Catalog
NJ228EM Cylindrical (NJ, 1-Dir Locating) 140 × 250 × 42 mm 395 / 515 kN 9.43 kg Transmission input & transfer-case shafts View Spec
NU228EM Cylindrical (NU, Non-Locating) 140 × 250 × 42 mm 395 / 515 kN 9.36 kg Floating-end gearbox thermal expansion View Spec
22322 CA/W33 Heavy Spherical (223, 1:12 K opt.) 110 × 240 × 80 mm 825 / 1,120 kN 17.6 kg Vibratory compactor drums & heavy pivots View Spec

Engineering Notice: Tapered roller rows list overall assembly width T per ISO 355 (outer cup width C noted for housing verification); cylindrical and spherical units follow ISO 15. International OEM cross-references indicate nominal envelope dimensions only—confirm contact angle, rib/retaining-ring geometry, and axial setting or clearance group per equipment drawing before substitution.

Four Engineering Checks for Earthmoving & Drivetrain Bearings

Avoid axle-hub overheating, planetary gear pitting, and premature shaft seizure by verifying these four field fundamentals.

1. Axial Preload & Overall Width T on Tapered Roller Pairs

Opposed 302 / 322 / 323 / 331 tapered roller pairs are set by axial end-play or controlled preload—never by radial feeler gauges. Always match overall width T (not cup width C alone) and verify contact-angle factor e when cross-referencing bevel-pinion and wheel-hub bearings.

Read Tapered Preload & Axial Setting Guide

2. Full-Complement (NCF / NNCF / NNCL) vs Caged (NJ / NU)

Cageless full-complement bearings maximize radial load density in low-speed crawler final drives, whereas machined-brass-caged NJ and NU bearings sustain higher rotational speeds with lower heat generation in powershift transmissions. Verify retaining-ring groove and axial float rules before swapping NCF, NNCF, and NNCL variants.

Read NCF / NNC / NNCL Engineering Guide

3. Locating (NJ) vs Floating (NU) & Residual Radial Clearance

Use NJ bearings strictly for one-direction axial location and NU bearings to allow internal thermal shaft growth within permissible displacement limits. On straight-bore cylindrical and spherical bearings, select unmounted CN or C3 clearance so mounted cold residual clearance transitions safely to hot operating clearance.

Read NJ / NU / NUP Clearance Guide

4. Jobsite Mud, Water & ISO Cross-Reference Discipline

Off-highway axles and excavator undercarriages operate immersed in abrasive slurry and shock loads. Pair ISO-verified bearings with duo-cone or multi-lip cassette seals, clean EP gear oil or NLGI #2 EP grease, and confirm full internal geometry rather than relying on nominal d × D × B/T matching alone.

Read ISO Bearing Cross-Reference Guide
ZQM precision roller bearing grinding and dimensional inspection workshop
Consistent Batch Quality for Construction OEMs & Fleet MRO ZQM supports aftermarket fleet overhaul kits and OEM drivetrain batches with verified ISO 355 / ISO 15 boundary dimensions, clean raceway finish, and export-ready corrosion protection.

Construction Machinery Bearing RFQ Checklist

Send these 5 details with your inquiry so our engineering team can confirm exact geometry, clearance, and stock availability:

  • Bearing Code or OEM Part Number: Full ISO designation or machine manual reference (plus d × D × B/T).
  • Machine Type & Assembly Position: Excavator final drive, loader wheel hub, bulldozer transmission, or compactor drum.
  • Structure & Setting Requirement: Opposed tapered pair, NCF / NNCF / NNCL full-complement, NJ / NU, or 222 / 223 spherical (CN / C3 / C4).
  • Lubrication & Contamination Exposure: SAE gear oil bath, EP grease, mud/water submersion, or vibratory shock service.
  • Batch Quantity & Delivery Window: Repair-kit sets or scheduled OEM production volume and target destination port.
Send Drivetrain Spec for Quote

Construction Machinery & Heavy Vehicle Bearing FAQs

Focused answers on tapered roller axial setting, full-complement final drives, and OEM cross-referencing.

How should axial preload or end-play be set on opposed 302 / 322 / 323 / 331 tapered roller bearings in heavy axles and transmissions?

Single-row tapered roller bearings are always mounted in opposed pairs (back-to-back O or face-to-face X arrangement) and adjusted via axial preload or axial end-play during assembly—never by radial feeler gauges. Verify overall bearing width T per ISO 355 (rather than inner ring B or outer cup C alone), shim or nut-adjust the pair to the OEM axial setting target, and account for shaft-housing thermal expansion under continuous grade haulage.

When do excavator travel drives and planetary gearboxes use full-complement NCF / NNCF / NNCL bearings instead of caged NJ / NU bearings?

Full-complement cageless cylindrical roller bearings (single-row NCF and double-row NNCF / NNCL) pack the maximum number of rollers into compact planetary hubs, cable sheaves, and low-speed travel reductions to handle extreme radial shock loads. Where input shafts or powershift transmissions run at higher rotational speeds, machined-brass-caged NJ (one-direction locating) and NU (non-locating floating) cylindrical roller bearings provide lower friction and higher limiting speeds.

What is the axial-location difference between NJ and NU cylindrical roller bearings in heavy construction gearboxes?

Both NJ and NU bearings carry heavy radial loads with straight cylindrical bores and separable rings for easier gearbox assembly. An NJ bearing has two outer-ring ribs and one inner-ring rib, locating the shaft axially in one direction only. An NU bearing has two outer-ring ribs and a ribless inner ring, acting as a non-locating bearing that accommodates shaft thermal expansion within permissible internal axial displacement limits.

What specifications should construction machinery OEMs and fleet MRO buyers send for a bearing quote?

Share the OEM part number or full ISO bearing designation (including d × D × B/T, taper series 302/322/323/331 or full-complement suffix NCF/NNCF/NNCL/V), assembly location (axle hub, final drive, powershift transmission, or vibrator drum), lubrication type (gear oil vs EP grease), sealing environment (mud, dust, water immersion), and order quantity. ZQM confirms nominal ISO boundary compatibility, clearance/setting notes, and delivery lead time.

Need Technical Verification for Construction Drivetrain Bearings?

Share your bearing designations, axle or gearbox dimensions, clearance/setting targets, and required volume. ZQM’s engineering and export team will confirm exact dimensional matching and factory lead times.

Scroll to Top