QJF1060X3MB Four-Point Contact Ball Bearing Overview
Engineered with a non-standard outer diameter of 459.5 mm (0.5 mm smaller than standard integer 460 mm QJ 1060 bearings), the QJF1060X3MB single-row four-point contact ball bearing (300 × 459.5 × 68 mm, reference mass 48.2 kg) handles bidirectional axial thrust in compact rolling mill chocks, heavy compressors, and gearbox locating stacks. Per ZQM Bearings’ 259-page general catalogue, it delivers a basic dynamic load rating Cr of 600 kN and basic static load rating C0r of 1,250 kN.
Critical Housing Fit Alert (-0.5 mm Special OD): The 459.5 mm outer diameter is intentionally undersized relative to a nominal 460 mm housing bore so the outer ring remains radially free (floating) and carries pure bidirectional axial load while an adjacent radial roller bearing supports 100% of radial force. Always verify housing bore dimensions and tolerances against your equipment drawing before ordering.
QJF1060X3MB Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 300 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 459.5 mm |
| Boundary Dimensions & Weight | Width (B) | 68 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 48.2 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 600 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 1250 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 900 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 1300 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 318 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 442 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 4.0 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 3 mm |
| Abutment & Fillet Dimensions | Load center distance (a) | 266 mm |
| Calculation Factors | Calculation factor (e) | 0.95 |
| Calculation Factors | Axial load factor (static) (Y0) | 0.58 |
| Calculation Factors | Axial load factor (Y1) | 0.66 |
| Calculation Factors | Axial load factor (Y2) | 1.07 |
| Calculation Factors | Radial load factor (X) | 0.6 |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
Structural Design and Axial Locating Engineering
- 35° Contact Angle & Split-Ring Architecture: Accommodates heavy reversing axial loads in both directions within a single 68 mm axial width (load center a = 266 mm), replacing back-to-back paired angular contact bearings where axial space is restricted.
- Cylindrical Bore (Non-Tapered): Manufactured with a straight 300 mm cylindrical bore; standard QJF bearings do not use tapered K sleeves.
- Machined Solid Cage (MB): Inner-ring guided machined solid cage construction suited for sustained industrial speeds (reference grease limit 900 r/min, oil limit 1,300 r/min); exact cage alloy and tolerance class are confirmed on the order drawing.
Typical Industrial Equipment Applications
- Steel Rolling Mill Locating Stacks: Paired beside four-row cylindrical rolling mill bearings (Steel and Rolling Mills Hub) to take pure bidirectional axial thrust.
- Heavy Helical Gearboxes & Compressors: High-speed input and intermediate shaft axial locating positions where radial loads are carried by adjacent NU/NJ cylindrical roller bearings.
- Large Vertical Pumps & Rotary Drives: Compact axial thrust control under reversing operating cycles.
ISO Nominal Cross-Reference for QJF1060X3MB
| Brand | Nominal Series Reference | Critical OD Check | Engineering Note |
|---|---|---|---|
| ZQM Bearings | QJF1060X3MB | 459.5 mm (-0.5 mm special OD) | Verified in ZQM 259-page General Catalogue |
| Standard ISO Series | QJ 1060 / QJF 10.. | 460 mm (standard integer OD) | NOT directly interchangeable on housing fit without verifying 459.5 vs 460 mm bore |
ISO Nominal Boundary Disclaimer: Cross-brand references indicate nominal bore/width series alignment only and do not promise drop-in interchangeability. Always confirm outer diameter (459.5 mm vs 460 mm), axial internal clearance, and housing drawings prior to replacement.
Mounting Abutment and Lubrication Guidelines
Verify shaft shoulder diameter da min = 318 mm, housing shoulder diameter Da max = 442 mm, and maximum fillet radius ra max = 3 mm. Ensure the outer ring is clamped axially with proper anti-rotation pin or radial clearance so it does not experience radial preloading. For speed-load evaluation, run your duty cycle in our ISO 281 Bearing Life Calculator or verify nomenclature in our Bearing Suffix Decoder.
Factory Quality Control and Export Supply
Manufactured at Wafangdian Qunma Bearing Manufacturing Co., Ltd. (ISO 9001 & ISO 14001 certified) with Ningbo export engineering support and Shanghai consolidation. Actual supplied clearance, tolerance class, and inspection documentation are confirmed in writing before production. Contact ZQM Bearings for drawing review and factory quotation.
Frequently Asked Questions — QJF1060X3MB
Why does QJF1060X3MB have a 459.5 mm outer diameter instead of 460 mm?
The 459.5 mm outer diameter is 0.5 mm smaller than the standard 460 mm QJ 1060 OD so the bearing sits radially free inside a nominal 460 mm housing bore. This prevents radial load from transferring into the four-point contact ball bearing when paired alongside a radial roller bearing.
Can I replace a 460 mm QJ 1060 directly with QJF1060X3MB (459.5 mm)?
Only if your equipment drawing specifies a radially floating 459.5 mm outer ring inside a 460 mm housing. Never substitute between 459.5 mm and 460 mm outer diameters without checking the housing bore tolerance and anti-rotation locking design.
What are the verified load ratings and weight of QJF1060X3MB?
Per ZQM Bearings’ catalog database, QJF1060X3MB (300 × 459.5 × 68 mm) has a basic dynamic load rating Cr of 600 kN, basic static load rating C0r of 1,250 kN, reference mass of 48.2 kg, and limiting speeds of 900 r/min (grease) / 1,300 r/min (oil).
Does QJF1060X3MB have a tapered bore?
No. QJF1060X3MB has a standard 300 mm straight cylindrical bore and does not mount on tapered K or K30 adapter sleeves.
What details should I send to quote QJF1060X3MB?
Provide designation QJF1060X3MB, confirm whether you require the 459.5 mm special OD (or standard 460 mm), specify clearance and quantity, and share your destination port via our Contact page.



