Dimensioned at 130 × 230 × 40 mm with a catalog weight of 7.56 kg per bearing, the 7226BM (7226 BM) single-row angular contact ball bearing delivers a basic dynamic load rating of 135 kN and a static load rating of 175 kN. Configured with a high-thrust 40° contact angle (B) and a solid machined brass cage (M), it is built specifically for API 610 multistage boiler-feed and refinery charge centrifugal pump thrust cartridges where balance-drum wear or suction cavitation drives sudden axial load reversals.
7226BM Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 130 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 230 mm |
| Boundary Dimensions & Weight | Width (B) | 40 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 7.56 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 135 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 175 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 1900 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 2800 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 144 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 216 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 3 mm |
| Abutment & Fillet Dimensions | Minimum flange chamfer (r34) | 1.1 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 2.5 mm |
| Abutment & Fillet Dimensions | Load center distance (a) | 95.5 mm |
| Calculation Factors | Calculation factor (e) | 1.14 |
| Calculation Factors | Axial load factor (static) (Y0) | 0.26 |
| Calculation Factors | Axial load factor (Y) | 0.57 |
| Calculation Factors | Radial load factor (X) | 0.35 |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
7226BM 40° High-Thrust Architecture for Balance-Drum Pumps
Multistage between-bearings pumps rely on an internal hydraulic balance drum or balance disc to cancel most of the discharge pressure acting across stacked impellers. Nevertheless, during cold boiler start-up, minimum-flow recycle transitions, or partial flashing at the first-stage eye, residual axial force spikes unpredictably—requiring a steep 40° (B) ball-to-raceway contact geometry.
- Extended Load-Center Spread (a = 95.5 mm): The 40° contact line projects 95.5 mm from the ring back face. Pairing two 7226BM units back-to-back (DB) creates a broad structural truss across the outboard bearing bracket, suppressing shaft whip near the mechanical seal faces.
- ISO 281 Axial Sensitivity: With catalog factors e = 1.14 and Y = 0.57, the 7226BM converts steep axial balance-drum loads efficiently without overloading outer-ring shoulder heights.
- Solid Brass Cage Endurance: Machined from dense brass alloy (M), the retainer withstands high-velocity oil-slinger turbulence and intermittent steam-flashing vibration far better than stamped sheet metal or glass-filled nylon retainers.
Outboard Thrust Cartridge Assembly & Abutment Precision
Because any single-row angular contact bearing restrains axial movement in one direction only, API 610 pump thrust housings universally specify a matched DB (back-to-back) pair of 7226BM rings locked solidly against a stepped shaft shoulder by a precision locknut and tab washer. On the non-drive coupling side, the paired outer rings sit inside a removable bolted thrust cartridge that sets rotor axial centrality relative to diffuser volutes.
Before installing fresh 7226BM bearings into a 130 mm pump shaft, verify machining accuracy against catalog boundaries: shaft shoulder abutment da ≥ 144 mm, housing shoulder Da ≤ 216 mm, and shoulder fillet radius strictly inside the r min = 3.0 mm bearing chamfer. Keep outer-ring housing fit loose enough for smooth axial thermal positioning during assembly while avoiding fretting rotation under 2-pole or 4-pole electric drive vibration.
Sump Lubrication, Oil-Ring Cooling & Speed Margin
Boiler-feed pumps driven by 4-pole motors or variable-speed steam turbines typically operate between 1,480 and 2,600 r/min—sitting close to the 7226BM’s catalog limiting speeds of 1,900 r/min (grease) and 2,800 r/min (oil). Consequently, grease packing is unsuitable for sustained high-speed feedwater duty; engineers deploy constant-level oil baths with brass oil flingers, oil-mist manifolds, or forced cooling-water jacketed bearing housings using ISO VG 32–46 rust-and-oxidation (R&O) inhibited turbine oil.
Pay close attention to oil level height: submerging the lowest ball beyond its midpoint triggers severe hydraulic churning inside a 230 mm OD housing, accelerating sump oxidation and closing matched DB clearance. Where operating shaft speeds approach the 2,800 r/min oil ceiling, verify oil-jet flow rate and bearing metal RTD alarm thresholds during shop hydro-mechanical runs.
7226BM Cross-Brand Nominal Equivalency Table
| Producer | Cross-Listed Part Number | Nominal Geometry & Suffix Notes (130 × 230 × 40 mm) |
|---|---|---|
| ZQM | 7226BM | 40° contact angle (B), solid machined brass cage (M) |
| SKF | 7226 BECBM / 7226 BM | 40° angle; BECBM indicates Explorer raceway, universal matchable flush-ground & brass cage |
| FAG / Schaeffler | 7226-B-XL-MP / 7226-B-MP | 40° contact angle (B), window-type solid machined brass retainer (MP) |
| NSK | 7226BM / 7226BMG | 40° contact angle (B), machined brass cage (M); G denotes universal matching |
| NTN | 7226BL1 / 7226BL1G | 40° angle (B) paired with machined brass cage (L1) |
Engineering Interchange Caution: The listing above maps nominal ISO 15 external dimensions (130 × 230 × 40 mm) only. Universal flush-ground end-face offsets, matched axial clearance classes (CA/CB/CC), and raceway heat-treatment profiles vary by manufacturer—never mix unmatched single bearings from different brands inside an API 610 thrust cartridge.
Ordering Matched 7226BM Pump Sets from ZQM
Power-plant maintenance engineers and multistage pump OEMs sourcing 7226BM should specify: matched DB set requirement (factory-ground paired serial sets or universal flush-ground), axial clearance band tuned for feedwater sump temperatures, lubrication regime (oil bath, oil mist, or forced circulation), and spare-set quantity. Every shipment undergoes factory dimensional, runout, and hardness inspection with full batch traceability. Request current stock lead time and matched-pair pricing through our factory quotation page.
7226BM Multistage Pump Bearing Q&A
Related Selection & Tools: Need drastically higher thrust and overhung moment capacity on the exact same 130 mm shaft? Compare the heavy 73-series 7326BM (280 × 58 mm), check fatigue life via our Bearing Life Calculator, decode cage/match suffixes with the Suffix Decoder, or browse all Angular Contact Ball Bearings and Industrial Sectors.
Why must API 610 boiler-feed pumps mount 7226BM in a matched DB pair?
A single 7226BM carries axial thrust in only one direction. During boiler start-up, load swings, or suction cavitation, hydraulic balance-drum pressure can momentarily reverse—so two matched 7226BM units in a back-to-back (DB) arrangement lock rotor position in both directions and widen the load-center span (a = 95.5 mm) to stabilize mechanical seals.
When should engineers upgrade from 7226BM to 7326BM on a 130 mm pump or mixer shaft?
Both share a 130 mm cylindrical bore and 40° brass-cage build, but 7226BM (230 × 40 mm, Cr 135 kN, C0r 175 kN) fits compact medium-section pump brackets, whereas 7326BM (280 × 58 mm, Cr 251 kN, C0r 270 kN) nearly doubles dynamic capacity for extreme vertical axial loads and cantilevered shaft bending.
Is grease lubrication acceptable for a 7226BM pair on a 2,400 r/min boiler-feed pump?
No. The catalog grease limiting speed for 7226BM is 1,900 r/min (oil limiting speed 2,800 r/min). High-speed feedwater pumps above 1,900 r/min require oil-bath cooling, oil-mist, or circulating turbine oil lubrication, and speeds approaching the 2,800 r/min oil ceiling demand careful thermal and oil-flow verification.
What shaft shoulder and chamfer dimensions govern 7226BM pump rebuilds?
Confirm shaft shoulder diameter da ≥ 144 mm, housing shoulder Da ≤ 216 mm, and shaft/housing fillet radius smaller than the bearing’s r min = 3.0 mm minimum chamfer so the inner and outer rings seat flush against perpendicular shoulders.



