Occupying the heavy ISO 03 cross-section at 130 × 280 × 58 mm and weighing a substantial 17.5 kg per ring assembly, the 7326BM (7326 BM) single-row angular contact ball bearing boosts dynamic capacity to 251 kN and static load capacity to 270 kN. Pairing a steep 40° contact angle (B) with a massive machined brass cage (M), it anchors the upper drive lantern of vertical chemical reactor agitators, pressurized autoclave mixers, and mineral-slurry leach tanks where suspended impeller weight, hydraulic pumping lift, and long cantilevered shaft bending converge.
7326BM Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 130 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 280 mm |
| Boundary Dimensions & Weight | Width (B) | 58 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 17.5 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 251 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 270 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 1800 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 2600 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 148 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 262 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 4 mm |
| Abutment & Fillet Dimensions | Minimum flange chamfer (r34) | 1.5 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 3 mm |
| Abutment & Fillet Dimensions | Load center distance (a) | 115.0 mm |
| Calculation Factors | Calculation factor (e) | 1.14 |
| Calculation Factors | Axial load factor (static) (Y0) | 0.26 |
| Calculation Factors | Axial load factor (Y) | 0.57 |
| Calculation Factors | Radial load factor (X) | 0.35 |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
7326BM Heavy 73-Series Stiffness & Overhung Moment Control
Long vertical agitator shafts often hang four to eight meters below the vessel nozzle without a submerged steady bushing in corrosive acid or viscous polymer slurries. Turbulent vortex shedding across pitched-blade turbines imposes cyclic side bending directly onto the drive-head bearing pedestal. Stepping up from 7226BM (230 × 40 mm, 7.56 kg) to 7326BM (280 × 58 mm, 17.5 kg) enlarges ball diameter and ring section thickness dramatically, raising dynamic capacity by 86% to 251 kN.
- 115.0 mm Load-Center Projection: At a 40° contact angle, each 7326BM projects its effective reaction apex a = 115.0 mm from the ring back face. Arranged back-to-back (DB) inside the agitator pedestal, two matched units resist severe cantilevered whip and keep double-mechanical-seal sleeves concentric.
- Bidirectional Vessel Pressure Thrust: Pressurized chemical reactors push upward on the shaft cross-section during high-bar reaction stages, while downward impeller weight and pumping reaction dominate during atmospheric drain-down; a matched DB pair handles both directions seamlessly using catalog constants e = 1.14 and Y = 0.57.
- Heavy Machined Brass Retainer (M): Thick-walled brass pockets withstand erratic slurry-chunk impact loads and low-speed boundary lubrication spikes without fracturing.
Vertical Agitator Pedestal Mounting & Abutment Integrity
Installing a 17.5 kg bearing pair on a vertical 130 mm agitator shaft requires disciplined lifting fixtures and controlled induction heating (never direct flame) so the straight cylindrical bore slides cleanly onto the shaft journal without scoring. Lock the inner rings tightly against the shaft shoulder using a high-torque hydraulic or tabbed locknut engineered to survive continuous shaft torsion reversals.
Check pedestal machining thoroughly against catalog mounting geometry: minimum shaft shoulder diameter da ≥ 148 mm, maximum housing bore shoulder Da ≤ 262 mm, and generous corner fillets clearing the heavy r min = 4.0 mm ring chamfer. Verify pedestal flange flatness bolted atop the reactor gearbox reducer—even minor bolt-up distortion twists a 280 mm outer ring and creates localized hot spots.
Vertical-Shaft Retention Grease & Oil-Bath Sealing Strategy
Most heavy chemical agitators run between 40 and 350 r/min—well below the 7326BM catalog ceilings of 1,800 r/min (grease) and 2,600 r/min (oil)—shifting engineering priority from high-RPM cooling to vertical lubricant retention and vapor-barrier sealing. In grease-lubricated lantern housings, gravity pulls lubricant downward out of the upper bearing unless a stepped grease retention plate sits closely beneath the lower ring and fresh NLGI 2 synthetic EP grease feeds from the top port.
Where gearbox oil splash or standalone vertical oil-bath reservoirs lubricate the 7326BM pair, install a reliable standpipe oil dam plus viton lip seals or labyrinth isolators below the lower bearing to prevent gear oil from weeping down into the reactor mechanical seal housing and contaminating process batches.
7326BM International Cross-Reference Matrix
| Manufacturer | Reference Part Number | Envelope & Internal Comparison (130 × 280 × 58 mm) |
|---|---|---|
| ZQM | 7326BM | 40° contact angle (B), heavy solid machined brass cage (M) |
| SKF | 7326 BECBM / 7326 BM | 40° contact angle; BECBM = Explorer internal design, universal matchable & brass cage |
| FAG / Schaeffler | 7326-B-XL-MP / 7326-B-MP | 40° angle (B) with solid machined window brass cage (MP) |
| NSK | 7326BM / 7326BMG | 40° contact angle (B), machined brass retainer (M); G = universal flush-ground |
| NTN | 7326BL1 / 7326BL1G | 40° contact angle (B), machined brass cage (L1) |
Interchange Scope Note: Cross-listed designations align strictly on ISO 15 boundary geometry (130 × 280 × 58 mm). Flush-ground paired end-face protrusion, internal axial clearance groups, and raceway geometry vary across suppliers; verify matched-set coding against your agitator gearbox drawing prior to plant turnaround substitution.
Sourcing 7326BM Agitator Pairs from ZQM Bearings
Chemical plant maintenance leads and industrial mixer OEMs requesting a 7326BM quote should outline: matched DB vs. DT arrangement (and whether an opposing auxiliary unit is used), shaft speed and reactor vessel pressure direction, preferred axial clearance class, and required delivery window. ZQM supplies verified factory dimensional, runout, and hardness inspection records with every batch and ships single turnaround pairs or OEM production crates worldwide. Reach our engineering sales desk via our direct inquiry portal.
7326BM Chemical Mixer & Agitator FAQ
Engineering Comparison & Tools: Compare lighter medium-series 130 mm 7226BM or 100 mm gearbox heavy-series 7320BM, run load-life projections on our Bearing Life Calculator, decode matched suffixes via the Suffix Decoder, or inspect our Industrial Gearboxes Hub and Angular Contact Ball Bearings.
How does a DB pair of 7326BM bearings protect vertical agitator mechanical seals?
With a 40° contact angle and 115.0 mm load-center projection per ring, two back-to-back 7326BM units build an exceptionally stiff overturning-moment anchor inside the drive pedestal. That rigidity curbs shaft deflection from unbalanced slurry vortices, keeping expensive double mechanical seals running true.
Can 7326BM handle upward reactor vessel pressure as well as downward shaft weight?
Yes—provided two matched 7326BM bearings are installed in an opposed DB (or DF) configuration. An individual single-row bearing only takes unidirectional axial force, whereas an opposed pair restrains both upward internal autoclave blow-out force and downward impeller weight.
What shaft abutment and fillet dimensions are mandatory for mounting 7326BM?
Because the 73-series carries a heavy ring cross-section, the minimum ring chamfer is r min = 4.0 mm. Machine shaft shoulders to da ≥ 148 mm and housing shoulders to Da ≤ 262 mm with transition fillets strictly below 4.0 mm so the bearing faces seat flat.
Why is grease retention hardware essential when running 7326BM vertically?
On vertical agitator shafts, gravity slowly drains base oil and soft grease downward through the lower bearing. Adding a close-clearance lower grease shield/baffle plate and feeding fresh synthetic EP grease from above keeps both DB rings continuously lubricated.



