7226BM Angular Contact Ball Bearing 130 × 230 × 40 mm

7226BM 40° angular contact ball bearing (130 × 230 × 40 mm, 7.56 kg, Cr 135 kN / C0r 175 kN) featuring a solid machined brass cage for API 610 multistage boiler-feed centrifugal pump back-to-back (DB) thrust cartridges handling severe hydraulic balance-drum reversals.

Request a Quote

Dimensioned at 130 × 230 × 40 mm with a catalog weight of 7.56 kg per bearing, the 7226BM (7226 BM) single-row angular contact ball bearing delivers a basic dynamic load rating of 135 kN and a static load rating of 175 kN. Configured with a high-thrust 40° contact angle (B) and a solid machined brass cage (M), it is built specifically for API 610 multistage boiler-feed and refinery charge centrifugal pump thrust cartridges where balance-drum wear or suction cavitation drives sudden axial load reversals.

7226BM Technical Specifications & Dimensions

Data Source: ZQM Factory PDF Catalogue DB (v1)Status: Catalogue Reference ValuesCatalogue Ref: 7226BM
Parameter CategoryTechnical Parameter (Symbol)Catalogue Reference Value
Boundary Dimensions & WeightBore diameter (d)130 mm
Boundary Dimensions & WeightOutside diameter (D)230 mm
Boundary Dimensions & WeightWidth (B)40 mm
Boundary Dimensions & WeightReference mass (Weight)7.56 kg
Load Ratings & Limiting SpeedsBasic dynamic load rating (Cr)135 kN
Load Ratings & Limiting SpeedsBasic static load rating (Cor)175 kN
Load Ratings & Limiting SpeedsLimiting speed (grease)1900 rpm
Load Ratings & Limiting SpeedsLimiting speed (oil)2800 rpm
Abutment & Fillet DimensionsShaft abutment diameter (da)144 mm
Abutment & Fillet DimensionsHousing abutment diameter (Da)216 mm
Abutment & Fillet DimensionsMinimum chamfer dimension (r12)3 mm
Abutment & Fillet DimensionsMinimum flange chamfer (r34)1.1 mm
Abutment & Fillet DimensionsMaximum fillet radius (ra)2.5 mm
Abutment & Fillet DimensionsLoad center distance (a)95.5 mm
Calculation FactorsCalculation factor (e)1.14
Calculation FactorsAxial load factor (static) (Y0)0.26
Calculation FactorsAxial load factor (Y)0.57
Calculation FactorsRadial load factor (X)0.35

Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.

7226BM 40° High-Thrust Architecture for Balance-Drum Pumps

Multistage between-bearings pumps rely on an internal hydraulic balance drum or balance disc to cancel most of the discharge pressure acting across stacked impellers. Nevertheless, during cold boiler start-up, minimum-flow recycle transitions, or partial flashing at the first-stage eye, residual axial force spikes unpredictably—requiring a steep 40° (B) ball-to-raceway contact geometry.

  • Extended Load-Center Spread (a = 95.5 mm): The 40° contact line projects 95.5 mm from the ring back face. Pairing two 7226BM units back-to-back (DB) creates a broad structural truss across the outboard bearing bracket, suppressing shaft whip near the mechanical seal faces.
  • ISO 281 Axial Sensitivity: With catalog factors e = 1.14 and Y = 0.57, the 7226BM converts steep axial balance-drum loads efficiently without overloading outer-ring shoulder heights.
  • Solid Brass Cage Endurance: Machined from dense brass alloy (M), the retainer withstands high-velocity oil-slinger turbulence and intermittent steam-flashing vibration far better than stamped sheet metal or glass-filled nylon retainers.

Outboard Thrust Cartridge Assembly & Abutment Precision

Because any single-row angular contact bearing restrains axial movement in one direction only, API 610 pump thrust housings universally specify a matched DB (back-to-back) pair of 7226BM rings locked solidly against a stepped shaft shoulder by a precision locknut and tab washer. On the non-drive coupling side, the paired outer rings sit inside a removable bolted thrust cartridge that sets rotor axial centrality relative to diffuser volutes.

Before installing fresh 7226BM bearings into a 130 mm pump shaft, verify machining accuracy against catalog boundaries: shaft shoulder abutment da ≥ 144 mm, housing shoulder Da ≤ 216 mm, and shoulder fillet radius strictly inside the r min = 3.0 mm bearing chamfer. Keep outer-ring housing fit loose enough for smooth axial thermal positioning during assembly while avoiding fretting rotation under 2-pole or 4-pole electric drive vibration.

Sump Lubrication, Oil-Ring Cooling & Speed Margin

Boiler-feed pumps driven by 4-pole motors or variable-speed steam turbines typically operate between 1,480 and 2,600 r/min—sitting close to the 7226BM’s catalog limiting speeds of 1,900 r/min (grease) and 2,800 r/min (oil). Consequently, grease packing is unsuitable for sustained high-speed feedwater duty; engineers deploy constant-level oil baths with brass oil flingers, oil-mist manifolds, or forced cooling-water jacketed bearing housings using ISO VG 32–46 rust-and-oxidation (R&O) inhibited turbine oil.

Pay close attention to oil level height: submerging the lowest ball beyond its midpoint triggers severe hydraulic churning inside a 230 mm OD housing, accelerating sump oxidation and closing matched DB clearance. Where operating shaft speeds approach the 2,800 r/min oil ceiling, verify oil-jet flow rate and bearing metal RTD alarm thresholds during shop hydro-mechanical runs.

7226BM Cross-Brand Nominal Equivalency Table

Producer Cross-Listed Part Number Nominal Geometry & Suffix Notes (130 × 230 × 40 mm)
ZQM 7226BM 40° contact angle (B), solid machined brass cage (M)
SKF 7226 BECBM / 7226 BM 40° angle; BECBM indicates Explorer raceway, universal matchable flush-ground & brass cage
FAG / Schaeffler 7226-B-XL-MP / 7226-B-MP 40° contact angle (B), window-type solid machined brass retainer (MP)
NSK 7226BM / 7226BMG 40° contact angle (B), machined brass cage (M); G denotes universal matching
NTN 7226BL1 / 7226BL1G 40° angle (B) paired with machined brass cage (L1)

Engineering Interchange Caution: The listing above maps nominal ISO 15 external dimensions (130 × 230 × 40 mm) only. Universal flush-ground end-face offsets, matched axial clearance classes (CA/CB/CC), and raceway heat-treatment profiles vary by manufacturer—never mix unmatched single bearings from different brands inside an API 610 thrust cartridge.

Ordering Matched 7226BM Pump Sets from ZQM

Power-plant maintenance engineers and multistage pump OEMs sourcing 7226BM should specify: matched DB set requirement (factory-ground paired serial sets or universal flush-ground), axial clearance band tuned for feedwater sump temperatures, lubrication regime (oil bath, oil mist, or forced circulation), and spare-set quantity. Every shipment undergoes factory dimensional, runout, and hardness inspection with full batch traceability. Request current stock lead time and matched-pair pricing through our factory quotation page.

7226BM Multistage Pump Bearing Q&A

Related Selection & Tools: Need drastically higher thrust and overhung moment capacity on the exact same 130 mm shaft? Compare the heavy 73-series 7326BM (280 × 58 mm), check fatigue life via our Bearing Life Calculator, decode cage/match suffixes with the Suffix Decoder, or browse all Angular Contact Ball Bearings and Industrial Sectors.

Why must API 610 boiler-feed pumps mount 7226BM in a matched DB pair?

A single 7226BM carries axial thrust in only one direction. During boiler start-up, load swings, or suction cavitation, hydraulic balance-drum pressure can momentarily reverse—so two matched 7226BM units in a back-to-back (DB) arrangement lock rotor position in both directions and widen the load-center span (a = 95.5 mm) to stabilize mechanical seals.

When should engineers upgrade from 7226BM to 7326BM on a 130 mm pump or mixer shaft?

Both share a 130 mm cylindrical bore and 40° brass-cage build, but 7226BM (230 × 40 mm, Cr 135 kN, C0r 175 kN) fits compact medium-section pump brackets, whereas 7326BM (280 × 58 mm, Cr 251 kN, C0r 270 kN) nearly doubles dynamic capacity for extreme vertical axial loads and cantilevered shaft bending.

Is grease lubrication acceptable for a 7226BM pair on a 2,400 r/min boiler-feed pump?

No. The catalog grease limiting speed for 7226BM is 1,900 r/min (oil limiting speed 2,800 r/min). High-speed feedwater pumps above 1,900 r/min require oil-bath cooling, oil-mist, or circulating turbine oil lubrication, and speeds approaching the 2,800 r/min oil ceiling demand careful thermal and oil-flow verification.

What shaft shoulder and chamfer dimensions govern 7226BM pump rebuilds?

Confirm shaft shoulder diameter da ≥ 144 mm, housing shoulder Da ≤ 216 mm, and shaft/housing fillet radius smaller than the bearing’s r min = 3.0 mm minimum chamfer so the inner and outer rings seat flush against perpendicular shoulders.

Scroll to Top