Sized at 120 × 215 × 40 mm with a verified unit mass of 6.04 kg, the 7224ACM (7224 ACM) single-row angular contact ball bearing combines a 146 kN basic dynamic rating and 184 kN static capacity inside an ISO 02 medium-series envelope. Engineered with a 25° contact angle (AC) and a solid machined brass retainer (M), it is purpose-matched to the discharge thrust end of high-speed oil-free rotary screw air compressors, where the helical male rotor demands tight end-face clearance control at elevated rotational velocity.
7224ACM Technical Specifications & Dimensions
| Parameter Category | Technical Parameter (Symbol) | Catalogue Reference Value |
|---|---|---|
| Boundary Dimensions & Weight | Bore diameter (d) | 120 mm |
| Boundary Dimensions & Weight | Outside diameter (D) | 215 mm |
| Boundary Dimensions & Weight | Width (B) | 40 mm |
| Boundary Dimensions & Weight | Reference mass (Weight) | 6.04 kg |
| Load Ratings & Limiting Speeds | Basic dynamic load rating (Cr) | 146 kN |
| Load Ratings & Limiting Speeds | Basic static load rating (Cor) | 184 kN |
| Load Ratings & Limiting Speeds | Limiting speed (grease) | 2200 rpm |
| Load Ratings & Limiting Speeds | Limiting speed (oil) | 3200 rpm |
| Abutment & Fillet Dimensions | Shaft abutment diameter (da) | 132 mm |
| Abutment & Fillet Dimensions | Housing abutment diameter (Da) | 203 mm |
| Abutment & Fillet Dimensions | Minimum chamfer dimension (r12) | 2.1 mm |
| Abutment & Fillet Dimensions | Minimum flange chamfer (r34) | 1.1 mm |
| Abutment & Fillet Dimensions | Maximum fillet radius (ra) | 2 mm |
| Abutment & Fillet Dimensions | Load center distance (a) | 59.1 mm |
| Calculation Factors | Calculation factor (e) | 0.68 |
| Calculation Factors | Axial load factor (static) (Y0) | 0.38 |
| Calculation Factors | Axial load factor (Y) | 0.87 |
| Calculation Factors | Radial load factor (X) | 0.42 |
Data source: ZQM Bearings online catalogue database (factory PDF catalogue v1). Load ratings, limiting speeds, and parameters without individual test records serve as catalogue reference values; verify shaft/housing shoulders (da, db, Da), tolerances, internal clearance, and drawings prior to ordering.
7224ACM 25° Contact Geometry & Rotor Thrust Mechanics
Oil-free dry-screw airends spin faster than comparable oil-flooded units to minimize internal gas blow-by across micron-scale interlobe clearances. Choosing a 25° (AC) contact angle instead of a steeper 40° raceway shortens the load-center projection to a = 59.1 mm, curbing gyroscopic ball spin and frictional heat inside compact discharge housings.
- Balanced Radial-Axial Load Factors: Catalog calculation parameters stand at e = 0.68 and Y = 0.87, allowing the 7224ACM to carry steady gas-pressure thrust from the compression chamber alongside helical timing-gear separation forces.
- Unidirectional Thrust Constraint: Because an individual 7224ACM supports axial thrust in a single direction only, compressor airends install two units back-to-back (DB) to lock forward discharge thrust and unload-cycle reverse drift, or tandem (DT) opposed by an auxiliary reverse bearing on high-pressure second stages.
- Machined Brass Cage Stability: Cut from solid copper-alloy stock, the M cage stays dimensionally true under rapid variable-frequency drive (VFD) ramp cycles and elevated gearcase oil temperatures up to its 3,200 r/min oil (2,200 r/min grease) catalog ceiling.
Male-Rotor Discharge End Fitment & Shoulder Control
In a two-stage dry-screw compressor, thermal growth of the steel male rotor drives directly toward the suction inlet while the discharge locating bearing anchors rotor end-float against the casing wall. Any excess axial play lets rotor lobes kiss the discharge endplate, causing catastrophic seizure; conversely, over-tightened shaft nuts provoke thermal runaway.
Airend rebuilders machining rotor shafts and bearing cartridges must hold catalog abutment limits: minimum shaft shoulder diameter da ≥ 132 mm, maximum housing shoulder diameter Da ≤ 203 mm, and corner fillet clearance respecting the bearing’s r min = 2.1 mm chamfer. Cylindrical shaft seating on the 120 mm bore typically uses a light interference fit paired with precision spacer sleeves so technicians can dial in factory axial endplay during cold assembly.
Pressurized Oil-Jet Cooling & Thermal Runaway Prevention
Unlike grease-packed electric motors, dry-screw compressor gearboxes separate the pressurized bearing oil gallery from the compression cavity via carbon-ring or labyrinth air seals. Directing filtered ISO VG 46–68 synthetic turbine oil through calibrated nozzles onto the gap between inner ring and brass cage removes frictional heat without excessive churning drag.
Maintain unobstructed drain passages immediately beneath the 7224ACM outer ring so hot oil evacuates freely; pooled lubricant trapped inside a 40 mm wide bearing cavity spikes sump temperature and collapses matched-pair axial clearance. Always flush timing-gear debris from oil coolers before commissioning a fresh discharge thrust set.
7224ACM Cross-Brand Nominal Reference
| Brand / Standard | Nominal Envelope Reference | Angle & Cage Notes (120 × 215 × 40 mm) |
|---|---|---|
| ZQM / GB/T 292 | 7224ACM | 25° contact angle (AC), solid machined brass cage (M) |
| NSK | 7224A5M / 7224AM | A5 designates 25° contact angle; standard A is 30° with machined brass cage (M) |
| SKF | 7224 ACD (precision) / 7224 BECBM (40°) | Check angle carefully: standard industrial SKF 7224 uses 40° (B); 25° ACD is precision series |
| FAG / Schaeffler | B7224-E (25°) / 7224-B-MP (40°) | 25° (E) appears in spindle series; industrial B-MP uses 40° with solid brass cage |
| NTN | 7224L1 (30°) | 30° standard angle with machined brass retainer (L1); verify load-center offset |
Boundary Mapping Notice: Equivalency above reflects ISO 15 nominal envelope dimensions (120 × 215 × 40 mm) exclusively and does not imply blind one-for-one swapability. Contact angle (25° vs. 30° vs. 40°), flush-ground end-face protrusion, and internal clearance vary across brands and must be checked against your airend build sheet.
Procuring 7224ACM Compressor Thrust Sets from ZQM
When issuing an RFQ for compressor airend overhauls or OEM assembly lines, note four details: pairing geometry (DB back-to-back or DT tandem), required matched axial clearance or light preload, precision class (standard P0, P6, or P5 runout), and delivery lot size. ZQM conducts full dimensional, radial runout, and Rockwell hardness verification prior to export packing, supporting both single-airend repair pairs and scheduled factory contracts. Submit your compressor part list via our engineering quotation desk.
7224ACM Compressor Bearing Q&A
Engineering Tools & Adjacent Sizes: Estimate fatigue service intervals with our Bearing Life Calculator, decode pair markings via the Bearing Suffix Decoder, compare the compact 140 mm 7028ACM, or browse all Angular Contact Ball Bearings and Industrial Sectors.
Why does a dry-screw compressor male rotor favor 25° 7224ACM over a 40° bearing?
At 120 × 215 × 40 mm, the 25° contact angle keeps spin-to-roll friction lower at speeds approaching 3,200 r/min in oil lubrication while still handling steady discharge gas thrust (Cr = 146 kN, e = 0.68). A steeper 40° angle generates higher heat at continuous compressor speeds when radial timing-gear forces are also significant.
Can one 7224ACM locate a screw compressor rotor by itself?
No. Every single-row angular contact ball bearing accepts axial thrust from only one side. Screw compressor discharge ends mount two 7224ACM units back-to-back (DB) to restrain both loaded discharge pressure and unloaded coast-down reversal, or use a tandem DT pair opposed by a reverse thrust bearing.
What shaft and housing shoulder dimensions must be verified during airend rebuilding?
Verify that the rotor shaft abutment measures at least da = 132 mm, the cartridge housing shoulder stays at or below Da = 203 mm, and shaft/housing fillet radii stay safely beneath the bearing’s r min = 2.1 mm chamfer to prevent corner riding.
How does the solid machined brass cage (M) perform under VFD speed cycling?
Machined brass retains pocket roundness and strength during frequent start-stop acceleration and pressurized synthetic oil exposure, avoiding the thermal creep and chemical embrittlement seen in molded polymer cages inside hot compressor gearcases.
What documentation and MOQ options apply when ordering 7224ACM from ZQM?
ZQM accommodates single-pair overhaul orders as well as recurring OEM batches, supplying standard factory dimensional, runout, and hardness inspection sheets. Specify DB/DF/DT pairing and clearance class when contacting our engineering team.



